INSTALLATION INSTRUCTIONS FOR PART 99-7328
APPLICATIONS
KIA Sorento
2007-2009
99-7328
KIT FEATURES
• Recessed DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate
B
C
A
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-7302 - Hyundai harness 2007-up
Antenna Adapter:
• Not required
TOOLS REQUIRED:
Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2007-2009 METRA ELECTRONICS CORPORATION
99-7328 DASH DISASSEMBLY
KIA SORENTO 2007-2009
A
1
2
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
Unclip and remove the side trim pan-
els. (Tip: start at the bottom of the
panels) (Figure A)
3
4
Remove (2) Phillips head screws
securing the radio trim panel. Unplug
and remove panel. (Figure B)
Remove (2) Phillips head screws
securing the vent panels then unclip
and remove the (2) vent panels.
(Figure C)
B
5
Remove (4) Phillips screws securing
the radio. Unplug and remove radio.
Continue to kit assembly.
C
1
99-7328 KIT ASSEMBLY
RECESSED DIN RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
Slide the DIN cage into the radio hous-
ing and secure by bending the metal
locking tabs outward. (Figure A)
1
2
Slide the radio into the DIN cage/hous-
ing assembly until it snaps into place.
(Figure B)
Continue to final assembly.
B
2
99-7328 KIT ASSEMBLY
ISO MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
Align the holes from the ISO snap in
brackets with the holes in the side of
the radio and mount the brackets to
the radio using screws supplied with
the radio. (Figure A)
1
2
3
Slide the radio/bracket assembly into
the radio housing until the assembly
snaps into place. (Figure B)
Snap the ISO Trim-plate onto the Radio
and housing assembly. (Figure B)
B
Continue to final assembly.
3
99-7328 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
4
99-7328
NOTES
5
99-7328 INSTRUCTIONS
1-800-221-0932
REV. 06/23/09 © COPYRIGHT 2007-2009 METRA ELECTRONICS CORPORATION INST99-7328
|