INSTALLATION INSTRUCTIONS FOR PART 95-7951
APPLICATIONS
CHEVROLET
Aveo 2004-2006
Aveo Hatchback-2007
SUZUKI
Forenza 2004-2008
Reno 2005-2008
Verona 2004-2007
PONTIAC
G3 Hatchback-2007
95-7951
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Double DIN Trim Plate • B) Double DIN Brackets
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
Wiring Harness:
• 70-2105 - GM harness 2006-up
• 70-8405 - GM/Suzuki/Daewoo harness 1999-up
Antenna Adapter:
B
A
• 40-CR10 - Chryler antenna adapter 2002-up
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
95-7951 DASH DISASSEMBLY
CHEVROLET AVEO 2004-2006
CHEVROLET AVEO HATCHBACK 2007
PONTIAC G3 HATCHBACK 2007
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
A
1
2
3
Unclip and remove the trim panels
from both sides of radio/climate con-
trols. (Figure A)
Remove (4) Phillips screws securing
the radio. Unplug and remove radio.
(Figure B)
Continue to kit assembly.
B
1
95-7951 DASH DISASSEMBLY
SUZUKI FORENZA 2004-2008
SUZUKI RENO 2005-2008
A
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
2
Disconnect air selector cable on dri-
ver’s side of center console behind
dash above accelerator pedal.
(Figure A & B)
3
Open glove box and remove (5)
Phillips screws ((3) on top and (2) on
bottom) then remove entire glove box.
B
Disconnect temperature selector
cable on passenger side of center
console behind glove box. (Figure C)
4
5
Unsnap and remove entire panel sur-
rounding radio. NOTE: The clips hold-
ing radio panel to dash are very
strong. (Figure D)
C
6
Remove (4) 10 MM bolts securing
radio. Unplug and remove radio.
(Figure E)
Continue to kit assembly.
Inside of Glove Box
D
E
BASS
MUTE
EQ
AM/FM
TAPE
CD
2
5
3
6
1
4
AST
TUNE
SCAN
2
95-7951 DASH DISASSEMBLY
SUZUKI VERONA 2004-2007
A
Disconnect the negative battery ter-
1
minal to prevent an accidental short
circuit.
2
3
Unclip and remove the trim panel sur-
rounding the radio. (Figure A)
Remove (4) Phillips screws from
radio. Unplug and remove radio.
(Figure B)
Continue to kit assembly.
B
3
95-7951 KIT ASSEMBLY
DOUBLE DIN MOUNT RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
NOTE: For the Chevrolet Aveo 2004-06,
Chevrolet Aveo Hatchback 2007, Pontiac
A
G3 Hatchback 2007 and Suzuki Verona
2004-07, cut and remove front lower mount-
ing tabs from the Double DIN trim plate
(Figure A). For the Suzuki Forenza 2004-07 and
the Suzuki Reno 2005-07, cut the rear lower
mounting tabs (Figure B).
NOTE: The Verona 2004-2007 sub dash
will need to be trimmed slightly for proper
fit. Refer to illustration.
(Figure C,D)
B
1
2
Snap the Double DIN brackets to the out-
side edge of the Double DIN trim plate.
(Figure E)
Slide the Double DIN radio into the brack-
et/trim plate assembly and secure the
radio to the assembly using the screws
supplied with the radio. (Figure F)
Continue to final assembly.
C
D
F
CUT
HERE
ON BOTH SIDES
E
4
95-7951 KIT ASSEMBLY
STACKED ISO MOUNT UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
NOTE: For the Chevrolet Aveo 2004-06,
Chevrolet Aveo Hatchback 2007, Pontiac
A
G3 Hatchback 2007 and Suzuki Verona
2004-07, cut and remove front lower mount-
ing tabs from the Double DIN trim plate
(Figure A). For the Suzuki Forenza 2004-07 and
the Suzuki Reno 2005-07, cut the rear lower
mounting tabs (Figure B).
NOTE: The Verona 2004-2007 sub dash will
need to be trimmed slightly for proper fit.
Refer to illustration.
(Figure C,D)
Snap the Double DIN brackets to the out-
side edge of the Double DIN trim plate.
(Figure E)
1
2
B
Slide the stacked ISO units into the brack-
et/trim plate assembly and secure the units
to the assembly using the screws supplied
with the units.e
(Figure F)
Continue to final assembly.
C
D
F
CUT
HERE
ON BOTH SIDES
E
5
95-7951 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
1-800-221-0932
REV. 06/02/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST95-7951
|