INSTALLATION INSTRUCTIONS FOR PART 95-7324
APPLICATIONS
KIA Optima
2006.5-2010
95-7324
KIT FEATURES
• Double DIN radio provision
• Stacked ISO units provision
KIT COMPONENTS
A) Double DIN Trim Plate • B) Double DIN Brackets
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-1004 - Hyundai 2006-up/KIA harness 2004-up
• 70-7303 - Hyundai / KIA Harness 2009
Antenna Adapter:
A
B
• 40-KI11 - 2009-10 Kia Optima
TOOLS REQUIRED:
Phillips Screwdriver • Small Flat Blade Screwdriver/ Panel Removal Tool
1-800-221-0932
© COPYRIGHT 2004-10 METRA ELECTRONICS CORPORATION
95-7324 DASH DISASSEMBLY
KIA OPTIMA 2006.5-2010
A
1
2
3
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
Unclip and remove the panel sur-
rounding the radio including the a/c
vents and climate controls. (Figure A)
Remove (4) Phillips screws securing
radio. Unplug and remove radio.
(Figure B)
B
Continue to kit assembly.
3:05
EQ
FM
AM
CD
103.5 FM
SCAN
AUDIO
POWER
1
2
5
3
RDM
FF
REW
SEEK
TRACK
4
6
RPT
TUNE
VOLUME
1
95-7324 KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
1
2
Snap the Double DIN brackets to
the inside edge of the Double DIN
trim plate. (Figure A)
Slide the Double DIN radio into the
bracket/trim plate assembly and
secure the radio to the assembly
using the screws supplied with the
radio. (Figure B)
Continue to final assembly.
B
2
95-7324 KIT ASSEMBLY
STACKED ISO UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
1
2
Snap the Double DIN brackets to
the inside edge of the Double DIN
trim plate. (Figure A)
Slide the stacked ISO units into the
bracket/radio housing assembly
and secure the units to the kit
using the screws supplied with the
units. (Figure B)
Continue to final assembly.
B
3
95-7324 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
4
95-7324
NOTES
5
95-7324 INSTRUCTIONS
1-800-221-0932
REV. 04/27/10 © COPYRIGHT 2004-10 METRA ELECTRONICS CORPORATION
INST95-7324
|