Operations and
Installation Manual
M3300CD
AM / FM Receiver with
CD Player
®
A Registered Trademark of Magnadyne Corporation
Location and Function of Controls at a Glance (continued)
6. Mode Button (MODE): Press the MODE button to change the operating mode as follows:
RADIO > CD* > USB* > SD* > AUX > RADIO.
*Available only when there is media inserted into Disc slot, SD card slot or USB slot.
��
7. Track Up Button (
l ): Adjusts the radio frequency, changes tracks and sets the clock.
8. SD Card Slot: Insert a SD card with the notch in the card facing up, “SD” will appear in the display
.
9. USB Input: Plug in your USB device, “USB” will appear in the display.
��
10. Track Down Button ( l
): Adjusts the radio frequency, changes tracks and sets the clock.
11. Radio Band Button (BAND): Selects the desired radio band in the following order: F1, F2, F3, A1 and A2.
12. Multi-Function Button (6, +10):
Radio: Recalls a memorized radio station, and programs a radio station into memory.
CD, SD or USB: Press to skip up 10 tracks.
13. Multi-Function Button (5, -10):
Radio: Recalls a memorized radio station, and programs a radio station into memory.
CD, SD or USB: Press to skip down 10 tracks.
14. Multi-Function Button (4, RDM):
Radio: Recalls a memorized radio station, and programs a radio station into memory.
CD, SD or USB: Press to randomly play tracks.
15. Multi-Function Button (3, INT):
Radio: Recalls a memorized radio station, and programs a radio station into memory.
CD, SD or USB: Press to activate the intro function which will play the beginning of every track for
10 seconds.
16. Multi-Function Button (2, RPT):
Radio: Recalls a memorized radio station, and programs a radio station into memory.
CD, SD or USB: Press to repeat the current track. Press again to cancel the repeat function.
�
17. Multi-Function Button (1, ll):
Radio: Recalls a memorized radio station, and programs a radio station into memory.
CD, SD or USB: Press to pause the current track. Press again to resume play.
18. AS/PS Button: Automatic radio station memory storing and preset radio station scanning.
19. 3.5mm Auxiliary Audio Input Jack: Plug in a device with a 3.5mm audio input plug.
20. Display Button: Press the DIS button to toggle through the available display information. In the radio
mode, program station name (PS) is the default, if not available the frequency will be displayed.
Toggle sequence: CT(clock/time)--PTY-- PS (program service, only if there is station)-- Exit Display.
3
Radio Operation
Select a Band
Local/Distant Reception
Press the MODE button until either F1, F2, F3, A1
or A2 appear in the display. Next press the BAND
button to select the desired band: F1, F2, F3, A1
or A2.
To narrow the reception to only local strong sta-
tion the radio must be switched from distant to
local reception. To switch from distant to local
reception push and hold the VOL knob for a
few seconds then release. Continue to press the
knob until “DX” appears in the display. Rotate
the VOL knob until “LOCAL” appears in the dis-
play. The unit will leave feature programing after
5 seconds of no button activity.
Tuning
��
Automatic Search Tuning: Press the
l or
��
l
button to move to the next or previous sta-
tion automatically.
��
��
Manual Tuning: Press and hold the
l or l
button until “MANUAL” appears in the display.
��
��
Then press and release the
l or l
but-
ton until desired frequency is selected. The unit
will default back to “AUTO” tuning mode after 5
seconds of no button activity.
RBDS Overview
RBDS (Radio Broadcast System) service avail-
ability varies from area to area. If RBDS service is
not available in your area, the following services
are not available:
Preset Stations
Six numbered preset buttons store and recall
PS: Program Service Name Broadcast - station
name data expressed in alphanumeric characters.
stations for each band. Select a band (if needed).
��
��
Select a station by pressing the
l or l
TP: Traffic Program Identification - for traffic
information broadcasting station.
button. Press and hold any of the preset buttons
for three seconds to memorize the station. The
preset number will appear in the display.
TA: Traffic Announcement Identification - show-
ing traffic information is being transmitted or not.
Recall a Station: Select a band (if needed). Press
one of the six preset buttons to select a stored
station.
TA (Travel Announcement) / TP (Travel Program
Identification)
Enable or disable TA mode by pressing and hold-
ing the BAND button. (Default is Disabled)
Automatic Preset Station Memory Store: Select a
band (if needed). Press and hold the button AS/
PS button for two seconds. The radio automati-
cally selects six strong stations and stores them
in the current band. The new stations replace
stations already stored in that band.
1. Long press BAND button once to activate the
function, press again to turn off the function.
2. When TA function is activated, it will search
the station with TA information automatically.
If there is not TA information, it will search the
station with TP information automatically, if
there is no TP information either, it will return
to the previous station after searching.
Note: During Automatic Memory Store, the unit
will search and store stations with the strong
signals first, and then weaker signal stations
until the memories are full.
Preset Scan: To scan preset stations stored in the
current band press the AS/PS button momentarily.
The radio pauses for five seconds at each preset
station. When the desired station is reached,
press the AS/PS button again to stop scanning.
3. When receiving the station with TP information
but without TA information, TP icon is on and
TA icon keeps blinking; when receiving the sta-
tion with TP and TA information, both TP and
TA icons are on.
FM Stereo/Mono Reception
4. When playing in another mode and TA infor-
mation is received, the unit will change to the
radio mode automatically. After the TA infor-
mation is finished, it will return to the previous
mode. The AS/PS, Preset (1-6), DIS, MODE,
For weaker FM stereo stations selecting mono
reception usually improves reception. To switch
from stereo to mono reception push and hold
the VOL knob for a few seconds then release.
Continue to press the knob until “STEREO”
appears in the display. Rotate the VOL knob until
“MONO” appears in the display. The unit will
leave feature programing after 5 seconds of no
button activity.
��
��
l , l
and BAND buttons are locked.
Press BAND button one to ignore the received
TA information, press BAND button twice to
turn off the function.
4
Radio Operation (continued)
PTY (Program Type)
TA Seek / TA Alarm
In TA Alarm mode, the alarm is set off.
1. Press and hold the VOL knob for a few sec-
onds then release.
1. Press and hold DIS button to activate the PTY
function.
2. Rotate the VOL knob to select the PTY type.
2. Continue to press the knob until “TA ALARM”
appears in the display.
3. When the program type you want to search for
is displayed, press the DIS button to search for
the selected program type. Press the DIS but-
ton again to stop the PTY search.
3. Rotate the VOL knob until “TA SEEK” appears
in the display. In TA SEEK mode, the unit will
seek for Traffic Announcement program.
Note: If PTY code is different or not available,
LCD blinks with “PTY NONE”.
Sound Controls
Volume
Loud
Rotate the VOL knob clockwise to increase the vol-
ume and counterclockwise to decrease the volume.
Enhances high frequency and low frequency
sound quality. To switch the loudness push
and hold the VOL knob for a few seconds then
release. Continue to press the knob until “LOUD
OFF” appears in the display. Rotate the VOL knob
until “LOUD ON” appears in the display. The unit
will leave feature programing after 5 seconds of
no button activity.
Sound Characteristics Menu
By pressing the VOL knob, the modes will be
displayed in the following order: Volume, Bass,
Treble, Balance and Fader.
Bass
Press the VOL knob two times. Turn the VOL knob
clockwise to increase the bass and counterclock-
wise to decrease the bass.
Mute
Press the PWR/MUTE button to turn the sound
off. Press it again to restore the audio.
Treble
Sub Woofer
Press the VOL knob button three times. Turn the
VOL knob clockwise to increase the treble and
counterclockwise to decrease the treble.
Press and hold the MODE button to enable or
disable the Sub Woofer output. When the Sub
Woofer output is enabled, “SW” appears in the
display.
Balance
Press the VOL knob button four times. Turn the
VOL knob clockwise to increase the balance to
the right and counterclockwise to increase the
balance to the left.
Fader
Press the VOL knob button five times. Turn the
VOL knob clockwise to increase the balance to the
front speakers and counterclockwise to increase
the balance to the rear speakers.
Equalizer
The M3300CD has pre-programmed audio set-
tings. To switch the equalizer settings push
and hold the VOL knob for a few seconds then
release. One of the following equalizer setting
will appear: POP M, ROCK M, DSP OFF, FLAT or
CLASSICS. Rotate the VOL knob until the desired
setting appears in the display. The unit will leave
equalizer programing after 5 seconds of no but-
ton activity.
Note: If the bass or treble is adjusted the equal-
izer setting will revert to the DSP OFF setting.
5
General Operations
Display Button
Turning the Unit On
The display feature allows you to see the clock
and information for the current operating mode.
Each press will change the information displayed.
Press any button to turn on the unit. Press and
hold PWR button to switch the unit off.
Mode:
Audio Beep
Press the MODE button to change the operating
Press and hold the VOL knob for a few seconds
then release. Continue to press the knob until
“BEEP 2ND” appears in the display. Rotate the
VOL knob to select the desired beep mode:
mode as follows:
RADIO > CD* > USB* > SD* > AUX > TUNER.
*Available only when there is media inserted
into Disc slot, SD card slot or USB slot.
BEEP 2ND = Beep on Press and Hold
BEEP ALL = When Pressing any Button.
BEEP OFF = No Beep Sound.
Setting the Clock
Press the DIS button so the clock is displayed.
Press the button again and hold for 3 seconds
until the time flashes, then release. Then press
��
The unit will leave feature programing after 5
seconds of no button activity.
the
the l
l button to adjust the minutes, and press
button to adjust the hours.
��
3.5mm Auxiliary Input Jack
Plug an audio device into this jack. This allows
you to listen to an auxiliary audio source (MP3
player, portable cassette player, etc). Connect
the proper cable (not supplied with this unit).
Press the MODE button until “AUX” appears in
the display to access the auxiliary device’s audio.
Note: The M3300CD will not control the auxiliary
audio source.
12 hr (am/pm) or 24 hr (military) Format
Press and hold the VOL knob for a few sec-
onds then release. Continue to press the knob
until “12 HOUR” appears in the display. Rotate
the VOL knob until “24 HOUR” appears in the
display. The unit will leave feature programing
after 5 seconds of no button activity.
CD, USB and SD Card Operation
Loading and Ejecting a CD
Insert a CD into the CD Slot, label side up, and the
CD will begin to play.
Fast Forward and Fast Reverse
��
��
Press the
l or l
button for more than one
second to fast forward or fast reverse. CD play
starts from when you release the button.
Press the EJ button to stop CD play and eject the
CD from the slot.
Pause Play
�
Press the 1/ ll button to pause play. Press it
again to resume play.
Inserting the SD Card or USB Device
Insert the SD card into the SD card slot and insert
a USB memory into the USB input. The mode will
automatically change to SD or USB mode.
Repeat the Same Track
Press the 2/RPT button to continuously repeat
the same track. Press it again to stop repeat.
Note: After finishing all tracks or all folders the unit
restarts playing all tracks for all folders automatically.
To remove the SD card:
Push in on the SD card until you hear a click,
then release the SD card and remove it.
To remove the USB memory:
Pull the USB memory out of the USB input.
Intro Scan
Press the 3/INT button to play the first ten sec-
onds of each track. Press it again to stop intro
scan and listen to the track.
Note: This unit may not play all SD cards or USB
memory devices. The manufacturer of this unit
is not responsible for any data loss. We suggest
you back-up your data.
Play All Tracks in Random Order
Press the 4/RDM button to play all tracks in random
order. Press it again to stop playing in random order.
Select Tracks
Press the
��
��
l or l
button for less than a
second to move to the next or previous track. The
track number appears in the display area.
Track Skip Buttons
Press the 5/-10 button to skip down 10 tracks.
Press the 6/+10 button to skip up 10 tracks.
6
CD, USB and SD Card Operation (continued)
File / Folder Search Function
File Name Search
When playing MP3/WMA files from a CD, USB
Memory or SD/MMC Card, press AS/PS button
to enter search mode.
1. Press AS/PS button until an asterisk “
“
*
blinks on left side of LCD.
2. Rotate the VOL knob to input letters (from A
to Z) or a number (from 0 to 9) of the file you
want to listen to.
Sequence of search modes:
File Number Search -> File Name Search ->
Folder Search -> Exit search mode.
3. Press the VOL knob to change to the next
character.
Note: Commercial audio-CD discs only support
file number search.
4. After completing input, press BAND/ENT but-
ton to play.
File Number Search
Note: If there is no file found, the unit will return
to initial input ready mode automatically.
1. Press AS/PS button to enter file number
search.
2. “MP3 T ” is displayed and the blinks to
show the unit is ready to accept a file number
to search for.
Folder Search
*
*
1. To start folder search, press the AS/PS button
3 times. The word “ROOT” will be displayed
on LCD, then the name of the first folder will
be displayed.
3. Rotate the VOL knob to input a digit, from 0 to
9, of the track you want to listen to.
4. Press the VOL knob to move to the next digit.
After completing input, press BAND/ENT but-
ton to play.
2. Rotate the VOL knob change the folder.
3. Press the BAND button to select the displayed
folder.
7
Installation Procedures
Brown Cable with Red/White RCA Connectors:
Provides Left and Right Channel audio signal output
for input to an additional amplifier.
S
tep 1: The radio chassis is designed to be “Sleeve
Mounted” through a opening in the dashboard panel.
The required opening size is 182mm (7-3/16”) x
52mm (2-1/16”). Cut or enlarged an opening in the
dashboard to accommodate the mounting sleeve.
Black Cable with Blue RCA Connector: Provides
Sub Woofer audio signal output for input to an
additional amplifier.
Step 2: If you are replacing an existing factory
installed radio, an adapter harness might be avail-
able for your vehicle to eliminate the need for
cutting your factory wiring. Contact Radio Shack
or other car stereo installation centers for the avail-
ability of a harness for your vehicle.
Note 1: This unit is designed to connect to (4) four
speakers. If the installation only requires (2) two
speakers, use the White and Gray wire sets to con-
nect the speakers.
Note 2: If installation angle exceeds 30 degrees
from horizontal, the unit might not give its optimum
performance.
Step 3: Insert the mounting sleeve into the hole in
the dashboard. Bend the metal tabs on the sleeve to
secure the mounting sleeve to the dashboard.
Step 4: Bring all wiring for the connection of the
unit (including the antenna) through the center of the
mounting sleeve. Connect the wiring as follows:
Note 3: Avoid installing the unit where it would be
subject to high temperature, such as from direct
sunlight, or from hot air, from the heater, or where is
would be subject to dust, dirt or excessive vibration.
Yellow Wire: Connect this wire to a constant +12
volt power source (a power source that is not con-
trolled by the ignition key).
Red Wire (with Fuse): Connect this wire to a
switched +12 volt power source (a power source
turned on and off by the ignition key).
Remove Transportation Screws: Before installing
the unit, please remove the two screws shown in
the illustration below.
Blue Wire: Connect this wire to the (+) power
antenna activation circuit or remote amplifier acti-
vation. If no power antenna or amplifier exists,
tape-off the end of this wire to prevent shorting
out the unit.
Remove Transportation
Screws Before
Installation
Black Wire: Connect this wire to the frame of the
vehicle (ground). This wire is the chassis grounding
wire for the unit.
White Wire: Connect this wire to the Left Front
Speaker (+) positive terminal or wire.
White Wire with Black Stripe: Connect this wire to the
Left Front Speaker (-) negative terminal or wire.
Green Wire with Black Stripe: Connect this wire to the
Left Rear Speaker (-) negative terminal or wire.
WARNING!
Green Wire: Connect this wire to the Left Rear
Speaker (+) positive terminal or wire.
Any wires left unconnected must be taped-off
or capped-off to prevent shorting.
DO NOT connect speaker ground wires together.
DO NOT connect speaker ground wires to the
chassis of the vehicle.
Gray Wire: Connect this wire to the Right Front
Speaker (+) positive terminal or wire.
Gray Wire with Black Stripe: Connect this wire to the
Right Front Speaker (-) negative terminal or wire.
DO NOT connect front and rear speaker wires
together.
Purple Wire with Black Stripe: Connect this wire to
the Right Rear Speaker (-) negative terminal or wire.
FAILURE TO FOLLOW ANY OF THESE
WARNINGS WILL RESULT IN DAMAGE TO
THIS UNIT AND VOIDS THE WARRANTY.
Purple Wire: Connect this wire to the Right Rear
Speaker (+) positive terminal or wire.
8
Wiring Diagram
Antenna
Socket
15 A
Fuse
Sub Woofer
Red Wire Ignition Switch (+12v in )
Yellow Wire Battery (+12v in)
Red
Right
Channel
Black Wire Ground (B-)
Audio Line Output
Blue Wire Power Antenna (Switched 12v out)
White
Left
Channel
Left
Front
Right
Front
Gray Wire
White Wire
Speaker
Speaker
Gray Wire with Black Stripe
White Wire with Black Stripe
Left
Rear
Speaker
Right
Rear
Speaker
Green Wire
Violet Wire
Green Wire with Black Stripe
Violet Wire with Black Stripe
9
Audio Line Out Connection
Cable Not Supplied
M3300CD
Optional
Speaker
Amplifier
Red (Right)
White (Left)
Sub Woofer Connection
Cable Not Supplied
M3300CD
Optional
Sub Woofer
Amplifier
Blue (Sub Woofer)
Final Installation - Method A
Mounting Sleeve
Sheet Metal
Screw
Nut
Washer
Metal Strap
Push Out Mounting
Sleeve Tabs
Dashboard
Removal Keys
Installing the Unit
Removing the Unit
1: Insert the sleeve into the dashboard opening and
1: Remove the trim ring.
bend the mounting tabs outward to secure it.
2: Insert the release keys into the left and right
2: If necessary, attach the mounting strap to the rear
side of the unit.
of the unit, then attach it with the supplied nut.
3: Pull the unit out of the dashboard.
3: Insert the unit into the sleeve until you hear a click.
4: Finally place the trim ring over the unit.
10
Final Installation - Method B
2
3
1
3
5
4
2
Installing the Unit
1: Screw holes on the side of the unit.
Note: The mounting sleeve, outer trim ring, and
the mounting strap are not used for this method of
installation.
2: Screws. Use wither truss screws (5 x 8mm) or
flush surface screws (4 x 8mm), depending on
the shape of the screw holes in the bracket.
3: Vehicle’s factory mounting bracket.
4: Dashboard or console.
5: Hook (Remove this part).
Specifications
General
Operating Power...... 12 VDC, Negative Ground
CD Player
Signal/Noise Ratio ............................... > 60 dB
Frequency Response ............... 20 Hz – 20 kHz
Channel Separation.............................. > 62 dB
Maximum Power Output.............. 4 x 45 Watts
RMS Power ................................. 4 x 19 Watts
RCA Line Out......Low-Level Outputs - 1000MV
Output Impedance ..Compatible 4-8 Ohm Speakers
Fuses .....................................................15 amp
Dimensions...... 178 (w) x 178 (d) x 51 (h) mm
FM Tuner
Tuner Range........................ 87.5 – 107.9 MHz
Usable Sensitivity ................................. 5 dBuV
Stereo Separation @ 1 kHz..................... 28 dB
AM Tuner
Tuner Range........................... 530 – 1710 kHz
Usable Sensitivity .................................... 30qV
Specifications are subject to change without notice.
11
Warranty
ONE (1) YEAR LIMITED WARRANTY
Magnadyne Corporation or its authorized agents will within one year from the date of sale to
you, repair, replace or refund the retail sales price of said product or any part thereof, at the
option of the Magnadyne Corporation or its authorized agents, if said product or part is found
defective in materials or workmanship, when properly connected and operating on the cor-
rect power requirements designated for the specific product. This warranty and Magnadyne
Corporation or its authorized agents obligations hereunder do not apply where the product
was; damaged while in the possession of the consumer, subjected to unreasonable or unin-
tended use, not reasonably maintained, utilized in commercial or industrial operations, or
serviced by anyone other than Magnadyne Corporation or its authorized agents, or where the
warning seal on the product is broken or the power and/or plugs are detached from the unit.
Magnadyne Corporation or any of its authorized agents will not assume any labor costs for
the removal and reinstallation of any product found to be defective, or the cost of transporta-
tion to Magnadyne Corporation or its authorized agents. Such cost are the sole responsibility
of the purchaser.
This warranty does not cover the cabinet appearance items or accessories used in connec-
tion with this product, or any damage to recording or recording tape, or any damage to the
products resulting from improper installation, alteration, accident, misuse, abuse or acts of
nature.
MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO
ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE
ACCORDED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN
EXCEPT THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND
ONE YEAR FROM THE DATE OF SALE.
This warranty extends only to the original purchaser of the product and is not
transferable. Some states do not allow limitations on how long an implied warranty lasts, and
some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitations or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may have other rights that vary from state to state.
Defective merchandise should be returned to the original point of purchase or
secondly, to:
Magnadyne Corporation
1111 W. Victoria Street
Compton CA 90220
Return Authorization must be obtained before sending, or merchandise may be refused.
© Copyright 2010 Magnadyne Corporation
M3300CD-UM Rev. A 1-5-11
|