CD-RECEIVER
KDC-W5641U
KDC-W5541U
KDC-W5141U
KDC-W5041U
KDC-W4141
KDC-W4041
INSTRUCTION MANUAL
© B64-3958-00/00 (EW/E2W)
Before use
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• The characters which can be displayed by this unit
are A-Z 0-9 @ " ‘ ` % & * + – = , . / \ < > [ ] ( ) : ; ^ - { } |
~ .
2WARNING
To prevent injury or fire, take the following
precautions:
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
<Demonstration mode Setting> (page 13).
• The RDS feature won’t work where the service is not
supported by any broadcasting station.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
How to reset your unit
• If this unit or the connected unit (disc auto changer,
etc.) fails to operate properly, press the Reset button.
The unit returns to factory settings when the Reset
button is pressed.
Handling CDs
• Do not touch the recording surface of the CD.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
Reset button
• Do not use disc type accessories.
• Clean from the center of the disc and move
outward.
• When removing CDs from this unit, pull them out
horizontally.
• If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen etc.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
¤
CDs that cannot be used
•
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.
• CDs that are not round cannot be used.
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty, wipe
them with a clean soft dry cloth.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
Lens Fogging
.
This unit may not correctly play discs which do not
have the mark.
• You cannot play a CD-R or CD-RW that has not been
finalized. (For the finalization process refer to your
CD-R/CD-RW writing software, and your CD-R/CD-
RW recorder instruction manual.)
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
English
|
3
Basic Operation
Display
D
Display Disc slot
Auxiliary input
[TI]
[M.JOG]
Release
ꢂ
[ ]
ꢀꢁ
[1] [2] [3] [4] [5] [6]
[SRC]
Control knob
USB Terminal
[
]
damaged by shocks or jolts.
General functions
•
•
Keep the faceplate in its faceplate case while detached.
Do not place the faceplate (and the faceplate case) in areas
exposed to direct sunlight, excessive heat or humidity. Also
avoid places with too much dust or the possibility of water
splashing.
Power/Source select button
Turns on the power.
[SRC]
When the power is on, the source switches between
Tuner (“TUNER”) , USB or iPod (“USB” or “iPod”),
CD (“CD”) , Auxiliary input (“AUX”), and Standby
(“STANDBY”) each time this button is pressed.
Press at least 1 second to turn off the power.
•
To prevent deterioration, do not touch the terminals of the
unit or faceplate with your fingers.
Auxiliary input
Auxiliary input
Used to connect a portable audio device with mini-
plug cable (3.5 ø).
⁄
•
•
•
•
When the power is ON, the <Security Code> (page 12) is
displayed as "CODE ON" or "CODE OFF".
⁄
•
Use the mini-plug cable (stereo) which does not have any
resistance.
For whether USB devices and iPod can be connected, refer
to <About Audio file> (page 15).
When an optional accessory is connected, the source name
for each device appears.
This unit automatically turns full power OFF after 20
minutes lapses in Standby mode in order to save the
vehicle's battery. The time until full power OFF can be set in
“POWER OFF” of <Menu System> (page 11).
When connection of the iPod is recognized, the source
display changes from "USB" to "iPod".
Muting volume upon reception of phone call
When there is a call, “CALL” is displayed and the audio
system is paused.
When the call ends, “CALL” disappears and the audio
system comes back on.
The audio system comes back on when [SRC] is
pressed during a call.
•
Volume control
Turn the knob to adjust the volume.
Control knob
Subwoofer output
Control knob
Switches between ON (“SUBWOOFER ON”) and OFF
(“SUBWOOFER OFF”) each time pushing toward down
for at least 2 seconds.
Faceplate release
Release
Releases the faceplate lock so that it can be removed.
Refer to the following diagram when reattaching the
faceplate.
Text/Title scroll
Control knob
Scrolls the CD, audio file, and Radio text display when
pushing toward up for at least 2 seconds.
Tuner functions
Band select
Control knob
Switches between FM1, FM2, and FM3 each time
pushing toward up.
¤
Switches to AM when pushing toward down.
•
The faceplate is a precision piece of equipment and can be
|
4
KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041
: Indicates the button etc. to operate.
Tuning
Control knob
Pause and play
[38]
Switches between pause and play each time this
button is pressed.
Changes the frequency when pushing toward left or
right.
⁄
Disc ejection
[0]
•
During reception of stereo stations the “ST” indicator is ON.
⁄
•
You can eject the disc for 10 minutes after switching off the
Traffic information
[TI]
engine.
Turns ON or OFF the Traffic Information function.
When the function is turned ON, “TI” indicator is ON.
If traffic bulletin starts when the function is ON,
“TRAFFIC INFO” is displayed and traffic information is
received.
USB device removing
[0]
Press this button for 2 seconds or longer to select
the remove mode, and the remove the USB device.
During the remove mode, “USB REMOVE” is displayed.
⁄
Music search
Control knob
•
If the volume is adjusted during reception of traffic
information, the adjusted volume is memorized
automatically. The memorized volume will be applied next
time the Traffic Information function is turned ON.
Changes the music when pushing toward left or right.
Fast reverses or forwards the music while keeping
pushing toward left or right. (No sound is output
while playing audio file.)
Preset memory
Memorizes the station selected when pressing for at
least 2 seconds.
[1] - [6]
Folder search
Control knob
Changes the folder containing the audio file when
pushing toward up or down.
Auto memory entry
Memorizes six stations with good reception
[TI]
Select mode
[M.JOG]
automatically when pressed for at least 2 seconds.
After pressing this button, you can quickly search
songs with the control knob. See <List Select> (page
10), <iPod Select> (page 10) for details.
Preset tuning
[1] - [6]
Recalls the memorized station.
Track/ File/ Folder repeat play
[4]
Disc & Audio file play functions
Switches between Track Repeat (“TRAC REP ON”) and
OFF (“REP OFF”) when pressed while playing a CD.
Switches between File Repeat (“FILE REP ON”), Folder
Repeat (“FOLD REP ON”), and OFF (“REP OFF”) when
pressed while playing an audio file.
Disc play
Disc slot
Starts playing when a disc is inserted.
When a CD is inserted, the “IN” indicator is ON.
⁄
⁄
•
•
3 inch (8 cm) CD cannot be used. Attempt to insert using
an adapter can cause malfunction.
The folder repeat operation cannot be performed while
iPod is playing.
USB device play (KDC-W5641U/W5541U/W5141U/
W5041U) USB Terminal
Used to connect the USB device to the USB cable
(optional accessory) which is connected to the USB
terminal.
Scan play
[2]
Successively plays the intro of the music in the disc or
folder.
When Scan Play is turned on, “TRAC SCAN ON”/ “FILE
SCAN ON” is displayed.
When the USB device is connected, the “USB”
indicator is ON.
⁄
•
The Scan paly operation cannot be performed while iPod is
playing.
⁄
•
For the playable audio file, media, and devices, refer to
<About Audio file> (page 15).
Random play
[3]
Randomly plays the music in the disc or folder.
When Random Play is turned on, “DISC RDM ON”/
“FOLD RDM ON” is displayed.
English
|
5
General Operation
Audio Control
Audio Setup
You can adjust following Audio Control items;
You can set Sound system , such as follows;
Adjustment Item Display
Range
0 — 35
–15 — +15
“L1”/”L2”/“OFF”(The
indicator turns on according to
the setting.)
Adjustment Item
Front High Pass Filter* “HPF F”
Display
Range
Through/80/100/120/ 150/180
Hz
Through/80/100/120/ 150/180
Hz
60*1/80/120/160*2/Through Hz
Rear volume*
Subwoofer level
Bass Boost**
“R-VOLUME”
“SUB-W L”
“B.BOOST-L”
Rear High Pass Filter* “HPF R”
Low Pass Filter
Subwoofer Phase*
Volume offset
Loudness*
Dual Zone System*
“LPF SW”
“PHASE”
Reverse (180°)/ Normal (0°)
System Q
“NATURAL”/
Natural/User setting/Rock/
“V-OFFSET” –8 — 0 (AUX: -8— +8)
“LOUDNESS” OFF/ON
“2ZONE”
“USER”/“ROCK”/ Pops/Easy/Top 40/Jazz
“POPS”/“EASY”/ (The indicator turns on
“TOP40”/“JAZZ” according to the setting.)
OFF/ON
Bass level
Middle level
Treble level
Balance
“BASS L”
“MID L”
“TRE L”
“BALANCE”
“FADER”
–8 — +8
–8 — +8
–8 — +8
Left 15 — Right 15
Rear 15 — Front 15
*Function of KDC-W5641U/W5541U/W5141U/W5041U.
*1KDC-W5641U/W5541U/W5141U/W5041U only.
*2KDC-W4141/W4041 only.
⁄
Fader
•
Volume offset: Sets each source’s volume as a difference
from the basic volume.
Exit Audio Control mode (Volume control mode)
•
Loudness: Compensates for low and high tones during
low volume. (Only the low tone is compensated for
when the tuner is selected as a source.)
Dual Zone System
Main source and sub source (Auxiliary input) output
Front channel and Rear channel separately.
- Set up the channel of sub source by “ZONE2” of <Menu
System> (page 11).
*Function of KDC-W5641U/W5541U/W5141U/W5041U.
**Function of KDC-W4141/W4041.
⁄
•
•
“USER”: The customized Bass, Middle, and Treble levels
are effective. On the KDC-W5641U/W5541U/W5141U/
W5041U, this item can be selected at any time. On the
KDC-W4141/W4041, this item is displayed only when
the tone quality has been adjusted. On the KDC-W4141/
W4041, this item disappears when another setting is
selected.
- Select Main source by [SRC] button.
- Adjust the volume of Front channel by Control knob.
- Adjust the volume of Rear channel by <Audio Control>
(page 6).
•
You can set Bass, Middle, and Treble for each source.
- The Audio Control has no effect on sub source.
1 Select the source to adjust
Press the [SRC] button.
1 Select the source to adjust
Press the [SRC] button.
2 Enter Audio Control mode
Press the Control knob.
2 Enter Audio Setup mode
Press the Control knob for at least 1 second.
3 Select the Audio item to adjust
Press the Control knob.
3 Select the Audio Setup item to adjust
Press the Control knob.
4 Adjust the Audio item
Turn the Control knob.
4 Adjust the Audio setup item
Turn the Control knob.
5 Exit Audio Control mode
Press any button.
Press a button other than the Control knob or 0
button.
5 Exit Audio Setup mode
Press the Control knob for at least 1 second.
|
6
KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041
Speaker Setting
Display Switching
Fine-tuning so that the System Q value is optimal
when setting the speaker type as follows;
Changes displayed information on each source
following;
Speaker type
OFF
For 5 & 4 in. speaker
For 6 & 6x9 in. speaker
For the OEM speaker
Display
In Tuner source
“SP SEL OFF”
“SP SEL 5/4”
“SP SEL 6*9/6”
“SP SEL OEM”
Information
Display
Program Service name or Frequency
Radio text, Program Service name or Frequency
Clock
“FREQUENCY/PS”
“RADIO TEXT”
“CLOCK”
1 Enter Standby
In CD & External disc source
Press the [SRC] button.
Information
Disc title
Track title (In External disc source)
Play time & Track number
Clock
Display
Select the “STANDBY” display.
“DISC TITLE”
“TRACK TITLE”
“P-TIME”
2 Enter Speaker Setting mode
Press the Control knob.
“CLOCK”
3 Select the Speaker type
Turn the Control knob.
In Audio file source
4 Exit Speaker Setting mode
Information
Display
Press the Control knob.
Music title & Artist name
Album name & Artist name
Folder name
File name
Play time & Music number
Clock
“TITLE/ARTIST”
“ALBUM/ARTIST”
“FOLDER NAME”
“FILE NAME”
“P-TIME”
“CLOCK”
In Standby/ Auxiliary input source
Information
Source name
Clock
Display
“SOURCE NAME”
“CLOCK”
1 Enter Switching Display mode
Press the [38] button for at least 1 second.
“DISPLAY SEL” is displayed.
2 Select the Display item
Push the Control knob towards right or left.
3 Exit Switching Display mode
Press the [38] button.
⁄
•
•
•
When you select the clock display, the display setting of
each source will be changed to the clock display.
If the selected display item does not have any
information, alternative information is displayed.
When selecting "FOLDER NAME" while playing with
iPod, names will be displayed depending on currently
selected browsing items.
English
|
7
Tuner Operation
is displayed. Select another Program Type.
PTY (Program Type)
Selecting the Program Type below and searching
for a station;
4 Exit PTY mode
Press the [38] button.
No.
Program Type
Display
1.
Speech
“SPEECH”
“MUSIC”
2.
Music
Program Type preset
Putting the Program Type in the Preset button
memory and quick recall.
3.
News
“NEWS”
4.
Current Affairs
Information
Sport
“AFFAIRS”
“INFO”
“SPORT”
5.
6.
Presetting the Program Type
7.
Education
Drama
“EDUCATE”
“DRAMA”
“CULTURE”
“SCIENCE”
“VARIED”
“POP M”
“ROCK M”
“EASY M”
“LIGHT M”
“CLASSICS”
“OTHER M”
“WEATHER”
“FINANCE”
“CHILDREN”
“SOCIAL”
“RELIGION”
“PHONE IN”
“TRAVEL”
“LEISURE”
“JAZZ”
“COUNTRY”
“NATION M”
“OLDIES”
“FOLK M”
“DOCUMENT”
8.
1 Select the Program Type to preset
9.
Culture
Refer to <PTY (Program Type)>.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
Science
Varied
2 Preset the Program Type
Press the desired [1] — [6] button for at least 2
seconds.
Pop Music
Rock Music
Easy Listening Music
Light Classical
Serious Classical
Other Music
Weather
Recalling the preset Program Type
1 Enter PTY mode
Refer to <PTY (Program Type)>.
Finance
Children’s programs
Social Affairs
Religion
2 Recall the Program Type
Press the desired [1] — [6] button.
Phone In
Travel
Leisure
Changing Language for PTY Function
Selecting the Program Type display language as
follows;
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
Language
English
French
Display
"ENGLISH"
"FRENCH"
"GERMAN"
⁄
•
German
Speech and Music include the Program type shown
below.
1 Enter PTY mode
Music: No.12 — 17, 26 — 30
Speech: No.3 — 11, 18 — 25, 31
Refer to <PTY (Program Type)>.
1 Enter PTY mode
2 Enter Changing Language mode
Press the [38] button.
Press the [TI] button.
During PTY mode the “PTY” indicator is ON.
3 Select the language
⁄
Push the Control knob towards up or down.
•
This function cannot be used during a traffic bulletin or
AM reception.
4 Exit Changing Language mode
Press the [TI] button.
2 Select the Program Type
Push the Control knob towards up or down.
3 Search for the selected Program Type station
Push the Control knob towards right or left.
⁄
•
When the selected Program Type is not found, “NO PTY”
|
8
KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041
Music disc/Audio file Operation
Function of remote control
Play Functions of Disc Changer
While a disc in the disc changer is being played, the
following play functions can be used.
Direct Access Tuning
Entering the frequency and tuning.
Playing the Current Song or Disc Repeatedly.
(Repeat play)
Press the [4] button.
1 Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
control.
Pressing the button repeatedly selects Track Repeat
play on (“TRAC REP ON”), Disc Repeat play on
(“DISC REP ON”), and Repeat play off (“REP OFF”)
sequentially.
"– – – –" is displayed.
2 Enter the frequency
Press the number buttons on the remote
control.
Randomly plays the music in the disc changer.
(Magazine random play)
Press the [6] button.
Pressing the button toggles the setting between
Magazine random play on (“MGZN RDM ON”) and
off (“RDM OFF”).
Example:
Desired frequency
92.1 MHz (FM)
Press button
[0], [9], [2], [1]
[0], [8], [1], [0]
810 kHz (AM)
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
Function of remote control
⁄
Direct Music Search
Searchs the music by entering the track number.
•
You can enter the FM band frequency in steps of a
minimum of 0.1 MHz.
1 Enter the music number
Press the number buttons on the remote
control.
2 Search the music
Press the [4] or [¢] button.
Cancelling Direct Music Search
Press the [38] button.
⁄
•
Direct Music Search cannot be performed during playing
of iPod, Random play, or scan play.
English
|
9
Music disc/Audio file Operation
Function of disc changers with remote control
Function of KDC-W5641U/KDC-W5541U
Function of iPod
Direct Disc Search
Searchs the disc by entering the disc number.
iPod Select
Search for the song you want to listen to by
selecting the same menu item as that of iPod.
1 Enter the disc number
Press the number buttons on the remote
control.
1 Enter Multi Jog Select mode
Press the [M.JOG] button.
“MULTI JOG ON” is displayed.
Displays the play list.
2 Search the disc
Press the [FM] or [AM] button.
Cancelling Direct Disc Search
Press the [38] button.
⁄
2 Searching for and playing a song
Operation type
Operation
Movement between items Turn the Control knob.
•
•
Input “0” to select disc 10.
Direct Disc Search cannot be performed during playing
of Random play or scan play.
Selection of item
Press the Control knob.
Return to previous item
Return to Top menu
Push the Control knob towards up.
Push the Control knob towards up for at
least 2 seconds.
Cancelling the Multi Jog Select mode
Press the [M.JOG] button.
Function of USB/CD of Audio file
List Select
Search for the song you want to listen to by tracing
the media file structure.
⁄
•
iPod Select cannot be performed during Random play.
1 Enter Multi Jog Select mode
Press the [M.JOG] button.
Function of Music CD
“MULTI JOG ON” is displayed.
Displays the current Audio file name.
Track Select
Select the song you want to listen to by turning the
control knob.
2 Searching for and playing a song
Operation type
Movement between
folders/files
Operation
1 Enter Multi Jog Select mode
Press the [M.JOG] button.
“MULTI JOG ON” is displayed.
Displays the current music No.
Turn the Control knob.
Selection of folder/flie
Press the Control knob.
Return to previous folder Push the Control knob towards left.
Return to root folder
Push the Control knob towards left for at
least 2 seconds.
2 Select the muisc
Turn the Control knob.
“<” or “>” beside the displayed folder name
indicates that this folder is preceded or followed by
another folder.
When file name is displayed, "✱" is added at the
end.
3 Play the selected song
Press the Control knob.
The Multi Jog Select mode is canceled and the
selected song is played.
Cancelling the Multi Jog Select mode
Press the [M.JOG] button.
Cancelling the Multi Jog Select mode
Press the [M.JOG] button.
⁄
⁄
•
Track Select is available only during playing of the built-
in CD player.
•
List Select cannot be performed during Random play or
scan play.
•
Track Select cannot be performed during Random play
or scan play.
|
10 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041
Menu Operation
Menu System
Set up the following functions;
Display
Setting Setting overview
Source
“RUSSIAN”*3 ON*/OFF Selects Russian as the display
language.
Display
Setting Setting overview
Source
—
“SCROLL”
AUTO/
Scrolls the screen once when the
“SECURITY Refer to
Sets security code
MANUAL* displayed text changes.
SET”
page 12
“AUX”
OFF/ON1*/ Sets whether to display AUX
“CLOCK
ADJUST”
Refer to
page 12
Sets the clock.
ON2
during source selection.
“POWER OFF” --- – 20M* Turns off the power when the
“SYNC”
ON*/OFF Synchronizing the RDS station
time data and this unit’s clock.
– 60M
preset time has lapsed in the
Standby mode.
—
—
“DISPLAY” ON*/OFF Turns off the display when no
operation is performed.
“CD READ” 1*/2
Sets the CD read mode.
Specifies whether to enable
—
“DEMO
MODE”
Refer to
page 13 demonstration.
“DIMMER”*1 AUTO*/OFF Dims the display in conjunction
with the light switch of the
vehicle.
“DIMMER”*2 ON/OFF* Adjusts the brightness of
the display according to the
surrounding illumination.
“DOT LINE” ON*/OFF Specifies whether to display the
red dotted line on the display.
* Factory setting
*1 Function of KDC-W5641U/W5541U/W5141U/W5041U.
*2 Function of KDC-W4141/W4041.
*3 Function of KDC-W5641U/W5141U/W4141.
Displayed item is depending on currently selected
source. The mark in Source column shows the
source to which the item is displayed.
: Can be set in other than standby state.
: Can be set in standby state.
“SWPRE”
REAR*/
SUB-W
Sets the preout output.
: Can be set while Audio file source of CD/USB
(excluding iPod).
: Can be set while Tuner source.
: Can be set during FM reception.
: Can be set while accessing AUX source.
“ZONE2”*1 REAR*/
FRONT
Specifies the destination of AUX
input sound when the Dual Zone
function is turned on.
“SUPREME” ON*/OFF Turns ON/OFF the Supreme
function.
—
: Can be set during all sources.
—
“NEWS”
OFF*
– 90M
Turns ON/OFF the News Bulletin
Automatic Reception function
and sets the news bulletin
interrupt disabled time.
1 Enter Menu mode
Press the [M.JOG] button for at least 1 second.
“MENU” is displayed.
“LOCAL S” ON/OFF* Only stations whose reception is
2 Select the menu item
good are searched in auto seek
tuning.
Push the Control knob towards up or down.
3 Set the menu item
“SEEK”
“AF”
AUTO1*/ Selects the tuning mode of
AUTO2/
the radio.
Push the Control knob towards right or left.
MANUAL
4 Exit Menu mode
ON*/OFF When station reception is poor,
automatically switches to the
station that is broadcasting the
same program over the same RDS
network.
Press the [M.JOG] button.
⁄
•
•
•
Refer to the respective page for information on how to
set the items with reference page number.
”ZONE2” is displayed when ”2ZONE” in <Audio Setup>
(page 6) is set to ”ON.
Refer to the <Appendix> (page 16) for the details of the
menu items.
“REGIONAL” ON*/OFF Sets whether to switch to the
station only in the specific region
using the“AF”control.
“ATPS”
ON*/OFF When traffic information station
reception is poor, automatically
searches for a station that can be
received better.
“MONO”
ON/OFF* Receives a stereo broadcast in the
mono mode.
“NAME SET” Refer to
Sets the display when switched
page 13 to AUX source.
English
|
11
Menu Operation
and the input prohibition periods shown in the table
below is generated.
After the input prohibition time lapses, “CODE” is
displayed, and you can reenter the code.
Security Code
When Security Code is set, possibility of theft
is reduced because input of Security Code is
prompted to turn on the unit once it is turned off.
Number of times the
Input prohibited time
incorrect code was input
⁄
1
2
3
4
—
5 minutes
1 hour
•
When you activate the Security Code function, it cannot be
released.
Note, your Security Code is the 4 digit number entered in
your “Car Audio Passport” in this package.
24 hours
1 Select Security Code item during Menu mode
Select the “SECURITY SET” display.
Manual Clock Adjustment
For how to select menu items, refer to <Menu
System>(page 11).
1 Select Clock Adjustment item during Menu
mode
Select the “CLOCK ADJUST” display.
For how to select menu items, refer to <Menu
System>(page 11).
2 Enter Security Code mode
Press the Control knob for at least 1 second.
When “ENTER” is displayed, “CODE” is also displayed.
3 Select the digits to enter
Push the Control knob towards right or left.
2 Enter Clock Adjust mode
Press the Control knob for at least 1 second.
The clock display blinks.
4 Select the Security Code numbers
Push the Control knob towards up or down.
5 Repeat steps 3 and 4, and complete the
3 Adjust the time
Security Code.
Push the control knob towards up or down to
adjust the hours and right or left to adjust the
minutes.
6 Confirm the Security Code
Press the Control knob for at least 3 seconds.
When “RE-ENTER” is displayed, “CODE” is also
displayed.
4 Exit Clock adjustment mode
Press the [M.JOG] button.
7 Do the step 3 through 6 step operation, and
reenter the security code.
“APPROVED” is displayed.
⁄
•
You can do this adjustment when the “SYNC” is set as
“OFF”.
The Security Code function activates.
⁄
•
If you enter a Code different from your Security Code,
you have to start over from step 3.
8 Exit Security Code mode
Press the [M.JOG] button.
Entering Security Code
The Security Code is required to use the audio unit
when the unit is first used after removed from the
battery power source or the Reset button is pressed.
1 Turn the power ON.
2 Do the step 3 through 6 step operation, and
reenter the security code.
“APPROVED” is displayed.
⁄
•
If an incorrect code is entered, “WAITING” is displayed,
|
12 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041
Auxiliary Input Display Setting
Selects the display below when changing to
Auxiliary input source;
• “AUX”
• “DVD”
• “PORTABLE”
• “GAME”
• “VIDEO”
• “TV”
1 Select Auxiliary input display setting item
during Menu mode
Select the “NAME SET” display.
For how to select menu items, refer to <Menu
System>(page 11).
2 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second.
The presently selected Auxiliary input display is
displayed.
3 Select the Auxiliary input display
Push the Control knob towards right or left.
4 Exit Auxiliary input display setting mode
Press the [M.JOG] button.
⁄
•
When operation stops for 10 seconds, the name at that
time is registered, and the Auxiliary input display setting
mode closes.
•
The Auxiliary input display can be set only when the
built-in auxiliary input or the auxiliary input of optional
KCA-S220A is used. On the KCA-S220A, "AUX EXT" is
displayed by default.
Demonstration mode Setting
Turning the demonstration mode ON/OFF.
1 Select Demonstration item during Menu mode
Select the “DEMO MODE” display.
For how to select menu items, refer to <Menu
System>(page 11).
2 Set the Demonstration mode
Press the Control knob for at least 2 second.
Pressing this button for 2 seconds or longer toggles
the setting between ”ON” and ”OFF”.
3 Exit Demonstration mode
Press the [M.JOG] button.
English
|
13
Accessory of KDC-W5641U/KDC-W5141U/KDC-W4141
Basic Operations of remote control
In Tuner source
SRC
ATT
VOL
AUD
SRC
AT T
Band select
[FM]/[AM]
VOL
AUD
Station select
[4]/[¢]
FM/AM
2-ZONE
0 — 9
Recall preset stations
[1] — [6]
DIRECT
*
In CD/USB source
Music select
[4]/[¢]
Folder/Disc select
[FM]/[AM]
*
Pause/Play
[38]
*KDC-W5641U/W5141U only
⁄
General control
About [
]
This button is used when Bluetooth HANDS FREE
BOX is connected. For more information, refer to the
instruction manual of Bluetooth HANDS FREE BOX.
Volume control
Source select
Volume reduce
[VOL]
[SRC]
[ATT]
¤
• Do not set the remote control in hot places such as
on the dashboard.
When the button is pressed again, the volume returns
to the previous level. When the volume is reduced,
the "ATT" indicator flashes.
Loading and Replacing battery
Use two “AA”/ “R6”-size batteries.
Slide the cover while pressing downwards to remove
it as illustrated.
Insert the batteries with the + and – poles aligned
properly, following the illustration inside the case.
In Audio control
Audio item select
[AUD]
[VOL]
Adjusts the Audio item
⁄
•
Refer to <Audio Control> (page 6) for the operation
method, such as the procedures for Audio control and
others operations.
Dual Zone control
Dual zone system on and off
Rear channel volume control
[2-ZONE]
[5]/ [∞]
|
14 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041
Appendix
About Audio file
About USB device
•
•
•
•
Playable Audio file
• If you start playback after connecting the iPod, the
music that has been played by the iPod is played
first.
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)
Playable disc media
CD-R/RW/ROM
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
USB device Playable Model
KDC-W5641U, KDC-W5541U, KDC-W5141U,
KDC-W5041U
In this case, "RESUMING" is displayed without
displaying a folder name, etc. Changing the browse
item will display a correct title, etc.
• When the iPod is connected to this unit,
“KENWOOD” or “✓” is displayed on the iPod to
indicate that you cannot operate the iPod.
• When the USB device is connected to this unit,
it can be charged up provided that this unit is
powered.
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
• You cannot connect a USB device via a USB hub and
Multi Card Reader.
• Take backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
•
•
•
Playable USB device
USB mass storage class
Playable USB device file system
FAT16, FAT32
iPod Playable Model
KDC-W5641U, KDC-W5541U
Although the audio files are complied with the
standards listed above, the play maybe impossible
depending on the types or conditions of media or
device.
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
<
v
:
Folder
Audiofile
CD
(ꢂ)
• When connecting the USB device, usage of the CA-
U1EX (option) is recommended.
Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 5 m can result in abnormal playback.
:
vꢀ
ꢁ
ꢃ
vꢆ
vꢇ
ꢅ
vꢄ
ꢈ
vꢉ
v.
An online manual about audio files is put on the
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
⁄
•
In this manual, the word "USB device" is used for flash
memories and digital audio players which have USB
terminals.
•
The word "iPod" appearing in this manual indicates the
iPod connected with the iPod connection cable (optional
accessory). The iPod connected with the iPod connection
cable can be controlled from this unit. iPods that can be
connected with the iPod connection cable are the iPod
nano, Fifth Generation iPod, iPod classic, and iPod touch.
Other iPods cannot be connected.
English
|
15
Appendix
•
SEEK (Tuning mode select)
Select a tuning mode of the radio.
Menu Glossary
•
SWPRE (Switching Preout)
Switches the preout between rear output (“REAR”)
and subwoofer output (“SUB-W”).
SUPREME
Tuning mode
Auto seek
Display Operation
“AUTO1” Automatic search for a station.
•
Preset station seek “AUTO2” Search in order of the stations in the
Preset memory.
Manual
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range
that is cut off when encoding at low bit rate (less
than 128Kbps, Sampling frequency is 44.1kHz).
Supplementing is optimized by compression
format (AAC, MP3 or WMA) and processed
according to bit rate.
The effect is negligible with music that is encoded
at high bit rate, variable bit rate or has minimal high
frequency range.
CD READ
Sets the method for reading CD.
When unable to play special format CD, set this
function to “2” to force playing. Note that some
music CD may be unplayable even when set to “2”.
In addition, audio files cannot be played when set
to “2”. Normally, keep this set to “1”.
“MANUAL” Normal manual tuning control.
•
•
AF (Alternative Frequency)
When the reception is poor, automatically alternate
to another frequency broadcasting the same
program in the same RDS network with better
reception.
RUSSIAN (Russian language setting)
When this is set to ON, the following character
strings are displayed in Russian:
Folder name/ File name/ Song title/ Artist name/
Album name/ KCA-BT100 (optional accessory)
•
1 : Automatically distinguishes between audio file
disc and music CD when playing disc.
2 : Forces playing as music CD.
•
POWER OFF (Power OFF Timer)
Setting the timer to turn this unit’s power OFF
automatically when Standby mode continues.
Using this setting can save the vehicle’s battery
power.
•
AUX
When this is set to ON, AUX source can be selected.
ON1: Outputs the sound of external unit connected
to the AUX terminal when switched to AUX
source.
– – –: Power OFF Timer function is OFF.
20M: Turns the power OFF after 20 minutes.
(Factory setting)
40M: Turns the power OFF after 40 minutes.
60M: Turns the power OFF after 60 minutes.
ZONE2 (Dual Zone)
Set the destination (front speaker “FRONT” or rear
speaker “REAR”) of the sub source (AUX IN) when
the Dual Zone function is turned on.
DISPLAY
If this unit is not operated at least 5 seconds with
“OFF” selected, the display turns off. During a setup
mode, the display will not turn off even if 5 seconds
lapse.
ON2: Activates the attenuator function when
switched to AUX source.
Turn off the attenuator function when
listening to output from external unit. This
prevents the noise when no external unit is
connected to AUX terminal.
•
•
OFF: Disables the selection of AUX source.
Set to OFF when not using the AUX terminal.
NEWS (News Bulletin with Timeout Setting)
Automatically receives news bulletin when it
starts. Set the time during which interrupt is to be
disabled after start of another news bulletin.
Changing ”NEWS 00M” to ”NEWS 90M” turns this
function ON. When this function is ON, the “NEWS”
indicator is ON.
•
If news bulletin starts when this function is ON,
“TRAFFIC” is displayed and news is received. If ”20M”
is has been set, reception of another news bulletin
will not start for 20 minutes.
The news bulletin volume is the same level that
was set for Traffic Information.
|
16 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041
This Product is not installed by the manufacturer of a
vehicle on the production line, nor by the professional
importer of a vehicle into an EU Member State.
For operating KCA-BT100
To control KCA-BT100, operate as follows;
To make setting for <Selecting the Dialing Mode>,
select <Menu System> (page 11). Pressing the [38]
button for at least 1 second after selecting the
"DIALING MODE" item allows you to enter the dialing
method selection mode. To exit from dialing method
selection mode, press [M.JOG] button.
To make <Disconnecting a Call>, <Clearing the
Disconnection Massage>, and <Rejecting an
Incoming call>, press [AUTO] button for at least 1
second.
Information on Disposal of Old Electrical
and Electronic Equipment (applicable for
EU countries that have adopted separate
waste collection systems)
Products with the symbol (crossed-out
wheeled bin) cannot be disposed as
household waste.
Old electrical and electronic equipment
should be recycled at a facility capable
of handling these items and their waste
byproducts. Contact your local authority
for details in locating a recycle facility
nearest to you. Proper recycling and waste
disposal will help conserve resources whilst
preventing detrimental effects on our
health and the environment.
Moreover, some displays are different from the
description of KCA-BT100 Instruction Manual.
Displays of KCA-BT100 Instruction Actual displays on this unit
Manual
“DISCONCT”
“CONNECT”
“PHN-DEL”
“P-STATUS”
“BT-CON Y”
“T-CON N”
“HF DISCONCT”
“HF CONNECT”
“DEVICE DEL”
“DVC STATUS”
“HF CONNECT Y”
“HF CONNECT N”
The marking of products using lasers
(Except for some areas)
: Displays the bluetooth connection status.
This indicator turns on when a cell-phone is
connected to this unit.
: Displays the signal strength of cell-phone.
: Displays the battery level of cell-phone.
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and says
that the component uses laser beams that have been
classified as Class 1. It means that the unit is utilizing
laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
Declaration of Conformity with regard to
the EMC Directive 2004/108/EC
Manufacturer:
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
EU Representative's:
Kenwood Electronics Europe BV
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands
English
|
17
Accessories/ Installation Procedure
with the ignition, connect the ignition wire to a power
source that can be turned on and off with the ignition key.
Use a commercially available conversion connector if the
connector does not fit in the vehicle connector.
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
Accessories
•
1
•
..........1
•
•
•
2
..........2
Installation Procedure
1. To prevent short circuits, remove the key from the
ignition and disconnect the - terminal of the
battery.
•
•
2. Make the proper input and output wire
connections for each unit.
3. Connect the wire on the wiring harness.
4. Take Connector B on the wiring harness and
connect it to the speaker connector in your vehicle.
5. Take Connector A on the wiring harness and
connect it to the external power connector on your
vehicle.
6. Connect the wiring harness connector to the unit.
7. Install the unit in your car.
8. Reconnect the - terminal of the battery.
9. Press the reset button.
About CD players/disc changers connected
to this unit
Kenwood disc changers/ CD players released in 1998
or later can be connected to this unit.
Refer to the catalog or consult your Kenwood dealer
for connectable models of disc changers/ CD players.
Note that any Kenwood disc changers/ CD players
released in 1997 or earlier and disc changers made by
other makers cannot be connected to this unit.
Connecting unsupported disc changers/CD players to
this unit may result in damage.
Set the “O-N” Switch to the “N” position for the
applicable Kenwood disc changers/ CD players.
The functions you can use and the information that
can be displayed may differ depending on the models
being connected.
¤
•
Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
•
•
Make sure to ground the unit to a negative 12V DC power
supply.
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
If the power is not turned ON (“PROTECT” is displayed),
the speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
•
•
•
•
Make sure that all wire connections are securely made by
inserting jacks until they lock completely.
If your vehicle’s ignition does not have an ACC position, or
if the ignition wire is connected to a power source with
constant voltage such as a battery wire, the power will not
be linked with the ignition (i.e., it will not turn on and off
along with the ignition). If you want to link the unit’s power
|
18 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041
Connecting Wires to Terminals
KDC-W5641U/W5541U/W5141U/W5041U
Steering remote control (Light Blue/Yellow)
REMO.CONT
L
R
R
Rear preout/SubWoofer preout
To use the steering wheel remote control feature, you need to an exclusive
remote adapter (not supplied) matches your car is required.
When this terminal is not in use, leave its cap on.
KDC-W4141/W4041
L
Rear/SubWoofer preout
R
FM/AM antenna input (JASO)
(KDC-W5641U/W5541U/W5141U/W5041U)
FM/AM antenna input (JASO)
(KDC-W4141/W4041)
To Kenwood disc changer/
External optional accessory
Fuse (10A)
Wiring harness
(Accessory1)
TEL mute wire (Brown)
Connect to the terminal that is grounded when
either the telephone rings or during conversation.
MUTE
⁄
To connect the Kenwood navigation system,
consult your navigation manual.
If no connections are made, do
not let the wire come out from
the tab.
Power control/ Motor
antenna control wire
(Blue/White)
Connect either to the power control terminal
when using the optional power amplifier, or to the
antenna control terminal in the vehicle.
P.CONT
ANT.CONT
Battery wire (Yellow)
Ignition wire (Red)
⁄
See next page.
A–7 Pin (Red)
A–4 Pin (Yellow)
Connector A
Connector B
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
English
|
19
Connecting Wires to Terminals
Connector Function Guide
Pin Numbers for Cable Colour
ISO Connectors
External Power
Connector
2WARNING
Functions
Connecting the ISO Connector
The pin arrangement for the ISO connectors depends on
the type of vehicle you drive. Make sure to make the proper
connections to prevent damage to the unit.
A-4
A-5
A-6
A-7
A-8
Yellow
Battery
Power Control
Dimmer*
Ignition (ACC)
Earth (Ground)
Connection
The default connection for the wiring harness is described in
1 below. If the ISO connector pins are set as described in 2
or 3, make the connection as illustrated.
Please be sure to reconnect the cable as shown 2 below to
install this unit to the Volkswagen vehicles etc.
Blue/White
Orange/White
Red
Black
Speaker
Connector
B-1
B-2
B-3
B-4
B-5
B-6
B-7
1(Default setting) The A-7 pin (red) of the vehicle’s
ISO connector is linked with the ignition, and the A-
4 pin (yellow) is connected to the constant power
supply.
Purple
Purple/Black
Gray
Gray/Black
White
White/Black
Green
Rear Right (+)
Rear Right (–)
Front Right (+)
Front Right (–)
Front Left (+)
Front Left (–)
Rear Left (+)
Rear Left (–)
Ignition cable (Red)
Unit
Battery cable (Yellow)
A-7 Pin (Red)
Vehicle
A-4 Pin (Yellow)
B-8
Green/Black
2The A-7 pin (red) of the vehicle’s ISO connector is
connected to the constant power supply, and the
A-4 pin (yellow) is linked to the ignition.
Ignition cable
*Function of KDC-W5641U/W5541U/W5141U/W5041U.
A-7 Pin (Red)
(Red)
Unit
Vehicle
A-4 Pin (Yellow)
Battery cable
(Yellow)
3The A-4 pin (yellow) of the vehicle’s ISO connector
is not connected to anything, while the A-7 pin
(red) is connected to the constant power supply
(or both the A-7 (red) and A-4 (yellow) pins are
connected to the constant power supply).
Ignition cable (Red)
Unit
Battery cable (Yellow)
A-7 Pin (Red)
Vehicle
A-4 Pin (Yellow)
⁄
•
When the connection is made as in 3 above, the unit’s
power will not be linked to the ignition key. For that reason,
always make sure to turn off the unit’s power when the
ignition is turned off.
To link the unit’s power to the ignition, connect the ignition
cable (ACC...red) to a power source that can be turned on
and off with the ignition key.
|
20 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041
Installation/Removing the Unit
Installation
Removing the hard rubber frame
Metal mounting strap
1 Engage the catch pins on the removal tool and
remove the two locks on the upper level.
Upper the frame and pull it forward as shown in
the figure.
(commercially available)
Firewall or metal support
Lock
Catch
Bend the tabs of the
Accessory2
mounting sleeve with a
screwdriver or similar utensil
and attach it in place.
Removal tool
2 When the upper level is removed, remove the
lower two locations.
Self-tapping screw
(commercially available)
⁄
•
The frame can be removed from the bottom side in the
same manner.
Screw (M4X8)
(commercially available)
⁄
Removing the Unit
•
Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (for example, the sound
may skip).
1 Refer to the section <Removing the hard rubber
frame> and then remove the hard rubber frame.
2 Remove the screw (M4 × 8) on the back panel.
3 Insert the two removal tools deeply into the slots
on each side, as shown.
4 Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
Screw (M4X8)
(commercially available)
Accessory2
¤
•
Be careful to avoid injury from the catch pins on the
removal tool.
5 Pull the unit all the way out with your hands, being
careful not to drop it.
English
|
21
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
Audio file source
? The sound skips when an Audio file is being
played.
!
• Cannot set up the subwoofer.
• Cannot set up the High Pass Filter.
• Cannot set up the Fader.
✔
✔
The media is scratched or dirty.
☞
Clean the media, referring to the CD cleaning of
the section on <Handling CDs> (page 3).
• No Audio control effect on AUX.
• Preout is not set to subwoofer. ☞ “SWPRE” of
<Menu System> (page 11)
The recording condition is bad.
Record the media again or use another media.
☞
• “Subwoofer output” of <Basic Operation> (page 4)
is not set to On.
• The Dual zone function is enabled. ☞ <Audio
Setup> (page 6)
!
!
Cannot set up the subwoofer phase.
The Low Pass Filter is set to Through. ☞ <Audio
Setup> (page 6)
• Cannot select the output destination of the
subsource in the Dual zone.
• Cannot adjust the volume of the rear speakers.
The Dual zone function is disabled. ☞ <Audio
Setup> (page 6)
!
!
• Cannot register a security code.
• Cannot set up Display Illumination Control.
<Demonstration mode Setting> (page 13) is not
turned off.
Cannot set up the Power-off timer.
<Security Code> (page 12) is not set.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
Tuner source
? Radio reception is poor.
✔
The car antenna is not extended.
☞
Pull the antenna out all the way.
Disc source
? The specified disc does not play, but another one
plays instead.
✔
✔
The specified CD is quite dirty.
Clean the CD.
The disc is loaded in a different slot from that
specified.
☞
☞
Eject the disc magazine and check the number
for the specified disc.
✔
The disc is severely scratched.
Try another disc instead.
☞
|
22 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041
USB ERROR/USB (Blink):
Some trouble may have occurred to the
The messages shown below display your
systems condition.
connected USB device.
➪ Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
TOC ERROR:
• No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
iPod ERROR:
Connection to the iPod has failed.
➪ Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 15) for information on supported
iPods.
➪ Remove the USB device and then
reconnect it.
E-05:
E-77:
The disc is unreadable.
The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the “E-
77” code does not disappear, consult your
nearest service center.
➪ Confirm that the software for the iPod is
the latest version.
E-99:
Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
➪ Check the disc magazine. And then press
the reset button on the unit. If the “E-99”
code does not disappear, consult your
nearest service center.
USB REMOVE: The Remove mode has been selected for the
USB device/iPod. You can remove the USB
device/iPod safely.
IN (Blink):
The CD player section is not operating
properly.
➪ Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
PROTECT:
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
➪ Wire or insulate the speaker cable
properly and press the reset button. If
the “PROTECT” code does not disappear,
consult your nearest service center.
NA FILE:
An Audio file is played with a format that this
unit can’t support.
COPY PRO:
A copy-protected file is played.
READ ERROR: The file system of the connected USB device
is broken.
➪ Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
NO DEVICE:
N/A DEVICE:
The USB device is selected as a source
although no USB device is connected.
➪ Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
An unsupported USB device is connected.
➪ Remove the USB device without entering
the remove mode.
NO MUSIC DATA/E-15:
• The connected USB device contains no
playable audio file.
• Media was played that doesn’t have data
recorded that the unit can play.
English
|
23
Specifications
FM tuner section
Frequency range (50 kHz space)
: 87.5 MHz – 108.0 MHz
Usable sensitivity (S/N = 26dB)
: 0.7 μV/75 Ω
Quieting Sensitivity (S/N = 46dB)
: 1.6 μV/75 Ω
Frequency response ( 3.0 dB)
: 30 Hz – 15 kHz
Signal to Noise ratio (MONO)
: 65 dB
Selectivity (DIN) ( 400 kHz)
: ≥ 80 dB
Stereo separation (1 kHz)
: 35 dB
USB Interface
(KDC-W5641U/W5541U/W5141U/W5041U)
USB Standard
: USB1.1/ 2.0
Maximum Supply current
: 500 mA
File System
: FAT16/ 32
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC ".m4a" files
Audio section
Maximum output power
: 50 W x 4
Full Bandwidth Power (at less than 1% THD)
: 30 W x 4
MW tuner section
Frequency range (9 kHz space)
: 531 kHz – 1611 kHz
Usable sensitivity (S/N = 20dB)
: 25 μV
Speaker Impedance
: 4 – 8 Ω
Tone action
LW tuner section
Frequency range
: 153 kHz – 281 kHz
Usable sensitivity (S/N = 20dB)
: 45 μV
Bass : 100 Hz 8 dB
Middle : 1 kHz 8 dB
Treble : 10 kHz 8 dB
Preout level / Load (CD)
: 2500 mV/10 kΩ
Preout impedance
: ≤ 600 Ω
CD player section
Laser diode
: GaAlAs
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 24 Bit
Spindle speed
: 500 – 200 rpm (CLV)
Wow & Flutter
: Below Measurable Limit
Frequency response ( 1 dB)
: 10 Hz – 20 kHz
Total harmonic distortion (1 kHz)
: 0.008 %
Auxiliary input
Frequency response ( 1 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 10 kΩ
General
Operating voltage (11 – 16V allowable)
: 14.4 V
Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 53 x 155 mm
Weight
: 1.40 kg
Signal to Noise ratio (1 kHz)
: 105 dB
Dynamic range
: 93 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC ".m4a" files
Specifications subject to change without notice.
|
24 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041
|