KDC-U7056DAB
KDC-U7056BT
KDC-U7056BTL
CQDu-RiEcCkEIVSERtart Guide
© 2012 JVC KENWOOD Corporation
B59-2188-10/01 (M)
• To display characters in the following
language, additional setting is required.
KDC-U7056DAB KDC-U7056BT
- Chinese
How to reset your unit
If the unit fails to operate properly, press the
Reset button. The unit returns to the factory
settings.
Refer to “Chinese”of <12-5. Initial
Reset button
settings>.
KDC-U7056BTL
- Arabic
- Persian
- Thai
Refer to “TAG Language”of <12-5. Initial
settings>.
About the discs used with this unit
• This unit can only play the CDs with
.
• The following discs cannot be used:
- A disc that is not round
- A disc with coloring on the recording
surface or a disc that is dirty
- A recordable/rewritable disc that has
not been finalized (For the finalization
process, refer to the instruction manual
that came with your disc writing
software or your disc recorder.)
- An 8 cm (3 inch) disc (An attempt
to insert using an adapter can cause
malfunction.)
The illustrations of the display and panel appearing
in this manual are examples used to explain more
clearly how the controls are used. Therefore, what
appears on the display in the illustrations may differ
from what appears on the display on the actual
equipment, and some of the images on the display
may be inapplicable.
Handling discs
! CAUTION
• Do not touch the recording surface of
the disc.
• Keep battery out of reach of children
and in original package until ready to
use. Dispose of used batteries promptly.
If swallowed, contact a physician
immediately.
• Do not stick tape etc. on the disc, or use a
disc with tape stuck on it.
• Do not use any accessories for the disc.
• Do not use any solvents to clean discs.
Use a dry silicon or soft cloth.
• Clean the disc by moving the cloth
outward from the center of the disc.
• When removing a disc from this unit, pull
it out horizontally.
• If the center hole or outside rim of a disc
has burrs, remove them before inserting
a disc.
• Do not leave the battery near fire or
under direct sunlight. A fire, explosion
or excessive heat generation may result.
• Do not set the remote control in hot
places such as on the dashboard.
• The Lithium battery is in danger of
explosion if replaced incorrectly.
Replace it only with the same or
equivalent type.
|
English
3
Appendix
Preparations
About Audio file
• Playable Audio files
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma),
WAV (.wav) of USB device
• Playable disc media
CD-R/RW/ROM
• Playable disc file formats
ISO 9660 Level 1/2, Joliet, Long file name.
• Playable USB devices
USB mass storage class
• Playable USB device file systems
FAT12, FAT16, FAT32
The online manual about
audio files is put on the site,
Before using this unit for the first
time
When this unit is first turned on, the
interactive menu appears for setting the
interface language and demonstration
mode. This menu disappears when no
action is taken for 15 seconds.
Models of iPods/iPhones that can
be connected to this unit
Made for
• iPod touch (4th generation)
• iPod touch (3rd generation)
• iPod touch (2nd generation)
• iPod touch (1st generation)
• iPod classic
1
KDC-U7056BTL only:
Select the interface language to display
the menu items of the Function setting,
from English, Arabic, and Persian.
Turn [Control] knob to select the
language, and then press [Control] knob.
• iPod with video
• iPod nano (6th generation)
• iPod nano (5th generation)
• iPod nano (4th generation)
• iPod nano (3rd generation)
• iPod nano (2nd generation)
• iPod nano (1st generation)
• iPhone 4S
• iPhone 4
• iPhone 3GS
• iPhone 3G
• iPhone
2
KDC-U7056BTL only:
If you selected English in step 1, select
the language to display the audio file
information, from English and Thai.
(Arabic or Persian is automatically
selected if you selected Persian or Arabic
in step 1.)
3 Press [Control] knob when the message
“To cancel DEMO Press the volume knob”
appears.
For information on the compatibility with
iPod/iPhone software, visit www.kenwood.
com/cs/ce/ipod/.
4 Turn [Control] knob to select “YES”, and
then press [Control] knob.
The interface language and
demonstration mode can also be set
with the Function setting. Refer to <12-
4. Demonstration mode setting> in
Instruction manual
|
4
Quick Start Guide
[Control] knob (Volume knob)
Release
1 6
/ ]
[
Adjusting the clock
Detaching/ Attaching the faceplate
1
Press [Control] knob to enter the
Function setting mode.
The item can be selected and
determined as follows.
”Settings”Á “Clock & Date”Á “Clock
Adjust”
Turn [Control] knob to select the item,
and press [Control] knob.
Press the
Release button.
2 Turn [Control] knob to adjust the hour,
and then press [Control] knob.
3 Turn [Control] knob to adjust the
minute, and then press [Control] knob.
4 Press and hold [1/6] to exits the
Function setting mode.
!
• Remove the faceplate at once after
pressing the Release button; otherwise it
can fall down due to vibration.
• The faceplate is a precision component of
the unit and can be damaged by shocks
or jolts.
• Keep the faceplate in its case while
detached.
• Do not place the faceplate (and case) in
areas exposed to direct sunlight, excessive
heat or humidity. Also avoid places with
too much dust or the possibility of water
splashing.
|
English
5
General operations
USB terminal
[SRC] [Control] knob (Volume knob)
Auxiliary input
Power
To turn the power ON, press [SRC].
To turn the power OFF, press and hold
Bluetooth audio
CD[1]
Auxiliary Input
“BT AUDIO”
“CD”
“AUX”
[SRC].
[1] This source can be selected only when it can
be played.
[2] Function of KDC-U7056DAB.
[3] Function of KDC-U7056BT.
Source selection
Pressing [SRC] repeatedly switches
among sources.
Volume
Source
Display
Turn [Control] knob to adjust the sound
Standby
“STANDBY”
“DIGITAL RADIO”
“TUNER”
volume.
Digital radio[2]
USB terminal
Tuner
A USB device or iPod can be connected.
The CA-U1EX (Max. 500mA) or KCA-iP102
(optional accessories) is recommended
to connect a USB device or iPod.
USB device connected to front USB
terminal
USB device connected to rear USB
terminal
“USB (FRONT)”
“USB (REAR)”
iPod connected to front USB terminal[1] “iPod (FRONT)”
iPod connected to rear USB terminal[1] “iPod (REAR)”
Pandora® of iPod connected to front “Pandora
Auxiliary input
A portable audio device can be
connected with a stereo mini-plug (3.5
mm ø).
USB terminal[1][2][3]
(FRONT)”
Pandora of iPod connected to rear USB “Pandora
terminal[1][2][3]
(REAR)”
Pandora of device connected via
Bluetooth[1][2][3]
“Pandora”
aha™ of iPod connected to front USB “aha (FRONT)”
terminal[1]
aha™ of iPod connected to rear USB “aha (REAR)”
terminal[1]
aha™ of device connected via
Bluetooth[1]
“aha”
|
6
Quick Start Guide
Playing music (CD/USB/iPod)
CA-U1EX[1]
Disc slot
G
[
]
Disc slot cover
[Control] knob
KCA-iP102[1]
REAR USB indicator
USB Terminal
1 6
E F R S
]
[
/
]
[
/
]
[
/
Playing a disc
Pause and play a song (track or
Open the Disc slot cover upward.
Insert a disc in the Disc slot.
When it is inserted, the source is
switched automatically and playback
starts.
file)
Press and hold [1/6].
Music search
You can search for the song you want to
play.
Close the Disc slot cover.
1
Press [1/6].
Playing a USB device/ iPod
Connect a USB device or iPod to the USB
terminal as shown above.
When it is connected, the source is
switched automatically and playback
starts.
You can connect the iPod or USB device
to either one of the USB terminals
provided at the front and rear of this unit.
If you connect it to the rear USB terminal,
2 Search for a song.
Operation type
Operation
Turn [Control] knob.
Press [Control] knob.
Selecting items
Determining selection
Returning to previous item Press [1/6].
To cancel music search in audio files or
iPod, Press and hold [1/6].
Ejecting disc
the “REAR USB”indicator stays lit.
[1] optional accessories
Open the Disc slot cover upward, and
press [G].
Selecting an audio file folder
Press [R] or [S].
Removing USB device/ iPod
Switch to a source other than USB,
iPod, Pandora, and Aha Radio, and then
remove the USB device.
Selecting a song (track or file)
Press [E] or [F].
Data contained in the USB device/ iPod
may be damaged if you remove it when
it is used as the active source.
Fast-forwarding or fast-
backwarding a song (track or file)
Press and hold [E] or [F].
|
English
7
Listening to the radio/Digital radio
[SRC]
[Control] knob
[
R
]
1 6
E F
]
[
/
]
[
/
4 Turn [Control] knob to select preset
number (FM/ Digital Radio: “1”– “18”,
AM: “1”– “6”), and then press and hold
[Control] knob.
Selecting a tuner source
Press [SRC] to select “TUNER”or “DIGITAL
RADIO”(KDC-U7056DAB only). Refer to
<Source selection> (page 6).
Recalling the stations in the
memory
Selecting a band (FM or AM)
(Tuner only)
Press [R].
1
Press [R] to select a band. (Tuner only)
2 Press [1/6].
Selecting a station/ service
Press [E] or [F].
3 Turn [Control] knob to select a preset
number (FM/ Digital Radio: “1”– “18”, AM:
“1”– “6”), and then press [Control] knob.
In the Mix Station preset mode, band
names of tuner sources are displayed as
follows:
The seek mode can be changed. Refer to
<9-5. Tuner setting> or <10-1. Listening
to the Digital Radio> in Instruction
manual
Station preset memory
FM: FM broadcast station
AM: AM broadcast station
1
Press [R] to select a band. (Tuner only)
2 Press [E] or [F] to select the
station/ service you want to save in the
station preset memory.
DR: Digital Radio service
3 “TUNER”: Press [1/6].
“DIGITAL RADIO”: Press [1/6] twice.
Press [1/6] again to enter the Mix
Station preset mode. In this mode,
different bands and tuner sources (FM,
AM, Digital Radio etc.) can be saved
in the same preset layer, which allows
you to recall a desired station without
switching between bands and/or tuner
sources. Maximum of 6 stations can be
preset in the Mix Station preset mode.
|
8
Quick Start Guide
Hands-free phoning
[Control] knob
Ú
[
]
Dialing a number in the phone
Pairing a Bluetooth device
You can pairing your Bluetooth device in
this unit.
book
Dial the phone number in the phone book
of your cell phone.
1
Operate the Bluetooth device to request
this unit for connection.
If the phone book has not been
downloaded to this unit, operate the cell
phone to download it.
The name of this unit (“KDC-####”)
appears on the Bluetooth device.
“Press the volume knob”appears.
1
Press [Ú].
2 Press [Control] knob.
2 Turn [Control] knob to select “Phone
Connection to your Bluetooth device
starts, “Pairing Success”appears a while
later, and then the previous source is
selected.
Book”, and then press [Control] knob.
3 Turn [Control] knob to select a name,
and then press [Control] knob.
4 Turn [Control] knob to select a phone
When registration of your cell phone is
completed, the phone book of the cell
phone is automatically downloaded
to this unit. (If the phone book has not
been downloaded to this unit, operate
the cell phone to download it.)
number.
5 Press [Ú].
Answering a phone call
Press [Ú].
Disconnecting a call
Press [Ú].
|
English
9
Before installation
you connect the + connector of the left
speaker to a front output terminal, do
not connect the - connector to a rear
output terminal.
• Connect the speaker wires correctly to the
corresponding terminals. The unit may
be damaged or fail to work if you share
the - wires or ground them to any metal
part in the car.
# WARNING
• The unit can only be installed in a car with
a 12V DC power supply, negative ground.
• If you connect the ignition wire (red)
and the battery wire (yellow) to the car
chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always
connect those wires to the power source
running through the fuse box.
• Do not use your own screws. Use only
the supplied screws. Using wrong screws,
could damage the unit.
!
CAUTION
• Use the power harness enclosed with this
unit for connecting power. Using a power
harness enclosed with other models can
cause malfunction.
• Install this unit in the console of your
vehicle.
• Do not touch the metal parts of this unit
during and shortly after use of the unit.
Metal parts such as the heat sink and
enclosure become hot.
• Mounting and wiring this product
requires skills and experience. For safety’s
sake, leave the mounting and wiring work
to professionals.
• If your car’s ignition key switch does
not have an ACC position, connect the
ignition wires to a power source that can
be turned on and off with the ignition
key. If you connect the ignition wires to
a constant-voltage power source, as with
battery wires, the battery may die.
• If the console has a lid, make sure to
install the unit so that the faceplate will
not hit the lid when it is closed or opened.
• After the installing the unit, check
whether the brake lamps, blinkers, wipers,
etc. on the car are working properly.
• Mount the unit so that the mounting
angle is 30° or less.
• If you experience any problem during
installation, consult your Kenwood dealer.
• Disconnect the battery’s negative terminal
before installing the unit.
• Reception may become poor if there are
metal objects near the Bluetooth antenna.
• Insulate unconnected wires with vinyl
tape or other similar materials. To prevent
a short circuit, do not remove the caps on
the ends of the unconnected wires and
terminals.
Bluetooth antenna unit
• Be sure to ground this unit to the car’s
chassis again after mounting.
• If the fuse blows, first make sure the wires
are not touching other parts to cause a
short circuit, and then replace the old fuse
with one with a new the same rating.
• When connecting only two speakers,
connect the connectors either to both
of the front output terminals or to both
of the rear output terminals (do not mix
front and rear terminals). For example, if
|
10 Quick Start Guide
KDC-U7056DAB
3
• This unit has the cooling fan to decrease
the internal temperature. Do not mount
the unit in a place where the cooling
fan of the unit are blocked. Blocking
these openings will inhibit the cooling
of the internal temperature and result in
malfunction.
.....4
.....4
4
Cooling fan
5
For Good Reception
.....1 (3m)
.....1
To assure good reception, note the
following:
6[1]
7[1]
8[1]
• Communicate with the cell phone within
the line-of-sight distance of 10 m (30
ft). The communication range becomes
shorter depending on the surrounding
environment. The communication
range also becomes shorter when there
is an obstacle between this unit and
the cell phone. The above maximum
communication range (10 m) is not
always assured.
.....1
• A broadcast station or walkie-talkie
located nearby can interfere with
communication due to a too strong
signal.
.....3
Installation accessories
9[1]
1
.....1
.....1
[1] KDC-U7056DAB only
2
.....2
|
English 11
Connecting wires to terminals
Rear output
R
L
Front output
Subwoofer output
Fuse (10A)
FM/AM antenna input
R
L
Digital radio antenna
(Accessory7)
(KDC-U7056DAB only)
Wiring harness
(Accessory1)
Microphone (Accessory5)
(KDC-U7056BT/
KDC-U7056BTL only)
White
White/Black
To front left speaker
To front right speaker
Gray
Gray/Black
Green
Green/Black
Purple
To rear left speaker
To rear right speaker
Purple/Black
<
Ignition key
switch
• Speaker Impedance: 4 – 8 Ω
Car fuse
box
ACC
Red (Ignition wire)
Car fuse box
(Main fuse)
Yellow (Battery wire)
Black (Ground wire) · (To car chassis)
+
–
Battery
KDC-U7056DAB only
|
12 Quick Start Guide
USB connector (0.8m)
To USB device.
USB maximum power supply current
: DC 5 V = 1 A
Microphone (Accessory5)
(KDC-U7056DAB only)
If no connections are made, do not let the wire come out from
the tab.
Blue/White
(Power control wire)
When using the optional power amplifier, connect
this wire to its power control terminal.
P.CONT
Depending on what antenna you are using, connect
either to the control terminal of the motor antenna,
or to the power terminal for the booster amplifier of
the film-type or short pole type antenna.
(Max. 300mA, 12V)
Blue (Antenna control wire)
ANT.
CONT
Brown (Mute control wire)
When connecting to the Kenwood navigation
system: Refer to your navigation manual.
MUTE
Orange/ White
(Dimmer control wire)
To car light control switch.
ILLUMI
Light Blue/ Yellow
(Steering remote control wire)
To use the steering wheel remote control feature,
an exclusive remote adapter (not supplied) that
matches your car is required.
REMOTE CONT
STEERING WHEEL
REMOTE INPUT
|
English 13
3 way speaker system setup
Connect the speaker wires
Tweeter output
R
L
Mid Range output
Woofer output
R
L
Wiring harness
(Accessory1)
White
White/Black
Gray
To MID Range left speaker
To MID Range right speaker
Gray/Black
Green
Green/Black
Purple
To left Tweeter
To right Tweeter
Purple/Black
Blue/White
(Power control wire)
When using the optional power amplifier,
connect this wire to its power control
terminal.
P.CONT
If no connections are made, do not
⁄
let the wire come out from the tab.
¤
Select a crossover mode according to
how the speakers are connected. Refer
to <2-Way/3-Way Crossover Setting>
(next page).
For how to connect speaker wires
If you select a wrong mode:
⁄
to terminals other than speaker
terminals and Preout terminals, refer
to <Connecting wires to terminals>
(page 12).
• The speakers can break.
• The output sound level may be
extremely low.
|
14 Quick Start Guide
2-Way/3-Way Crossover Setting
Select a crossover mode 2-way or 3-way
according to how the speakers are
connected.
1
Press the [SRC] to select “STANDBY”.
2 Pressing down the [S] and [E]s for at
least 3 seconds, allows you to enter the
2-way/3-way crossover setting mode.
3 The currently selected crossover mode
is displayed.
To change it, turn [Control] knob to
select “YES”, and then press [Control]
knob.
4 A confirmation screen appears.
If you are sure you want to change the
crossover mode, turn the [Control]
knob to select “YES”, and then press the
[Control] knob.
5 The newly selected crossover mode is
displayed, canceling the 2-way/3-way
crossover setting mode.
|
English 15
Installing/Removing the unit
Non-Japanese cars
Removing the trim plate
1
Engage the catch pins on the extraction
key (Accessory2) and release the two
locks on the upper part of frame.
Lift up and pull the frame forward as
shown in the figure.
Catch
Lock
Bend the tabs of the mounting sleeve
with a screwdriver or the like and
attach it in place.
Accessory2
<
2
When the upper part of frame is
removed, remove the lower part of frame.
• Make sure that the unit is installed
securely in place. If the unit is unstable, it
may malfunction (for example, the sound
may skip).
<
• The frame can be removed from the
bottom side in the same manner.
Japanese cars
1
Remove the trim plate with reference to
<Removing the trim plate>.
Removing the unit
Remove the trim plate with reference to
<Removing the trim plate>.
1
2 Align the holes in the unit (two locations
on each side) with the vehicle mounting
bracket and secure the unit with the
accessory screws.
2 Remove the faceplate.
3 Insert the two extraction keys
(Accessory2) deeply into the slots on
both sides as shown.
4 Lower the extraction key toward the
bottom, and then pull out the unit
halfway while pressing the extraction key
towards the inside.
Accessory2
3
4
8 mm
MAX.
8mm
MAX.
ø5mm
ø5mm
!
• Be careful to avoid injury from the catch
5pPinusllothnethuenietxatlrlatchteiownakyeyo.ut with your
hands, being careful not to drop it.
|
16 Quick Start Guide
KDC-U7056DAB only
Installing the
Microphone unit
Installing the Digital
radio antenna
!
CAUTION
1
Check the installation position of the
microphone (Accessory 5).
• This film antenna is exclusively for use
inside the vehicle.
2 Clean the installation surface.
• Do not install at the following locations:
- Where it may block driver’s view
- Where it may obstruct operation of
safety devices such as air bags
- On movable glass surface such as rear
hatch
• Signal strength will decrease at the
following locations:
- On IR reflecting glass or where covered
with mirror type glass film
3 Install the microphone.
4 Lay the cable up to the unit with it
secured at several positions using tape
or the like.
<
• Install the microphone as far as possible
from the cell phone.
- Where it overlaps with genuine radio
antenna (pattern)
Accessory5
- Where it overlaps with window heating
wires
- At side of vehicle (e.g. door, front
quarter window)
- On rear window
- When glass that blocks radio signals
(e.g. IR reflecting glass, thermal
insulation glass) is used
- Reception may decrease due to noise
when windshield wiper, air conditioner,
or motor is turned on.
Fix the cable with a commercial item of tape.
- Reception may decrease depending on
the direction of the broadcast station
with respect to the vehicle (antenna).
• Be sure to check the installation location
of film antenna (Accessory 6) before
installing. Film antenna cannot be
re-pasted.
Remove the separator of
the microphone, and stick
the microphone to the
place shown above.
• Thoroughly wipe oil and dirt from the
pasting surface with the included cleaner
(Accessory 9).
• Do not bend or damage the film antenna
(Accessory 6).
Adjust the direction of the
microphone to the driver.
• Warm the pasting surface by turning on
the heater for example, before applying.
• It may not be possible to install on some
type of vehicle.
• Check the cable routing of the film
antenna (Accessory 6) and amplifier
(Accessory 7) before pasting.
|
English 17
KDC-U7056DAB only
Installing the Digital radio antenna
Installation overview
Determining the antenna
installation location
• When installing the antenna on the
left side
Accessory67
Front pillar
150 mm
Earth sheet
Antenna cable (3.5 m)
70 mm*
• The antenna should be installed on the
passenger side for safety.
Accessory6
• Use cord clamper (Accessory 8) to
secure the antenna to the pillar at several
locations.
• The direction of the antenna film
(Accessory 6) changes depending on
whether the film antenna is installed on
the right side or left side.
Accessory7
• When installing the antenna on the
right side
Front pillar
Accessory7
• Separate the antenna film (Accessory 6)
from the ceramic line (black part) at the
top of the front glass by 150 mm.
Also, place it about 70 mm inside the
ceramic line at the side end of the front
glass. (where the earth sheet of the
amplifier can be pasted on the metal part
of the front pillar)
Earth sheet
150 mm
Accessory6
• Separate from other antennas by at least
100 mm.
70 mm*
• Do not paste the amplifier (Accessory 7)
on the ceramic line (black part) around
the front glass. Because there is not
enough adhesion.
*Where the earth sheet of amplifier unit
(Accessory 7) can be pasted on the metal
part of the front pillar.
|
18 Quick Start Guide
5 After pasting, rub the element in the
glass surface in the direction of the arrow
shown in the figure to bond it.
Antenna Installation
1
Check the installation location.
2 Clean the area where antenna film
(Accessory 6), amplifier unit (Accessory
7), and earth sheet are pasted with the
included cleaner (Accessory 9).
The coating on the metal surface need
not be removed.
• Wait until the glass surface is
completely dry before pasting.
• If the glass surface is cold, such as
during winter, warm it with defroster or
dryer.
3 Remove the separator (tag I) of antenna
film horizontally and paste the antenna
on the front glass.
6 Remove the application film (tag III).
• Do not touch the feeder terminal of
the element. Also, do not apply any
glass cleaner.
Feeder terminal
7 Match the protrusion of the amplifier
with the 5 on the antenna film and
paste.
• Do not touch the feeder terminal or
the pasting surface (adhesive side) of
the amplifier.
• Remove the separator gently.
• Do not touch the pasting surface
(adhesive side) of the antenna film.
4 Remove the separator (tag II) of antenna
film vertically and paste the antenna
gently while applying pressure.
• When installing the antenna on the
right side
Match the protrusion with 5
Earth sheet
Accessory6
Accessory7
|
English 19
KDC-U7056DAB only
Installing the Digital radio antenna
• When installing the antenna on the
<
left side
• Take the following precautions when
Accessory7
passing the antenna cable inside the front
pillar where the air bag is installed.
- Install the amplifier part of the antenna
cable in front or above the air bag so
that the antenna and the air bag do not
interfere.
Accessory6
Earth sheet
Accessory7
Match the protrusion with 5
8 Remove the film covering the earth
sheet and paste the earth sheet on the
metal part of the vehicle.
Provide sufficient leeway for the earth
sheet so that it does not interfere with
the interior parts (front pillar cover).
Also take care that the interior parts do
not interfere with the amplifier.
Air bag
Front pillar
- The front pillar cover is secured with
a special clip which may need to be
replaced when the front pillar cover is
removed.
Front glass
Accessory7
Front pillar
Contact your vehicle dealer for details
on replacing the front pillar cover and
availability of replacement parts.
Interior part
Earth sheet
Interior part
Clip
9 Wire the antenna cables.
• Use cord clamper (Accessory 8) to
secure the antenna to the pillar at
several locations.
|
20 Quick Start Guide
Audio section
Specifications
Maximum output power : 50 W x 4
Full Bandwidth Power (at less than 1% THD)
FM tuner section
: 22 W x 4
Frequency range
200 kHz step : 87.9 MHz – 107.9 MHz
50 kHz step : 87.5 MHz – 108.0 MHz
Usable sensitivity (S/N = 26dB)
: 7.2dBf (0.63 μV/75 Ω)
Quieting Sensitivity (S/N = 46dB)
: 15.2dBf (1.6 μV/75 Ω)
Frequency response (±3 dB) : 30 Hz – 15 kHz
Signal to Noise ratio (MONO) : 75 dB
Stereo separation (1 kHz) : 45 dB
Preout level/ Load (CD)
KDC-U7056DAB : 2500 mV/10 kΩ
KDC-U7056BT/ KDC-U7056BTL : 4000 mV/10 kΩ
Preout impedance : ≤ 600 Ω
Speaker Impedance : 4 – 8 Ω
Tone:
Band1 : 62.5 Hz ±9 dB, Band2 : 100 Hz ±9 dB
Band3 : 160 Hz ±9 dB, Band4 : 250 Hz ±9 dB
Band5 : 400 Hz ±9 dB, Band6 : 630 Hz ±9 dB
Band7 : 1 kHz ±9 dB,
Band8 : 1.6 kHz ±9 dB
Band9 : 2.5 kHz ±9 dB, Band10 : 4 kHz ±9 dB
Band11 : 6.3 kHz ±9 dB, Band12 : 10 kHz ±9 dB
Band13 : 16 kHz ±9 dB
AM tuner section
Frequency range
10 kHz step : 530 kHz – 1700 kHz
9 kHz step : 531 kHz – 1611 kHz
Usable sensitivity (S/N = 20dB) : 31 dBµ (36 µV)
Bluetooth section
Version : Bluetooth Ver. 2.1+EDR Certified
Frequency range : 2.402 – 2.480 GHz
Output Power
DAB tuner section (KDC-U7056DAB)
: +4dBm (MAX), 0dBm (AVE) Power Class 2
Frequency range
L-BAND : 1452.960 MHz – 1490.624 MHz
BAND III : 174.928 MHz – 239.200 MHz
Sensitivity : -100 dBm
Signal to Noise ratio : 80 dB
Antenna Connector type : SMB
Antenna Output Voltage (11 – 16V) : 14.4 V
Antenna Maximun Current : <100 mA
Maximum Communication range
: Line of sight approx.10m
Profiles
: HFP (Hands Free Profile)
: SPP (Serial Port Profile)
: PBAP (Phonebook Access Profile)
: OPP (Object Push Profile)
: A2DP (Advanced Audio Distribution Profile)
: AVRCP (Audio/Video Remote Control Profile)
CD player section
Auxiliary input
Laser diode : GaAlAs
Digital filter (D/A) : 8 Times Over Sampling
D/A Converter : 24 Bit
Spindle speed (Audio files) : 500 – 200 rpm (CLV)
Wow & Flutter : Below Measurable Limit
Frequency response (±1 dB) : 10 Hz – 20 kHz
Total harmonic distortion (1 kHz) : 0.008 %
Signal to Noise ratio (1 kHz) : 110 dB
Dynamic range : 93 dB
Frequency response (±3 dB) : 20 Hz – 20 kHz
Input Maximum Voltage : 1200 mV
Input Impedance : 10 kΩ
General
Operating voltage : 14.4 V (10.5 – 16V allowable)
Maximum Current consumption : 10 A
Installation Size (W x H x D) : 182 x 53 x 159 mm
Weight : 1.3 kg
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
Specifications subject to change without notice.
AAC decode : AAC-LC “.m4a” files
USB interface
USB Standard : USB1.1/ 2.0 (Full speed)
File System : FAT12/16/ 32
Maximum Supply current : DC 5 V
Decode : MP3, WMA, AAC, WAV
1 A
|
English 21
Requirements Pandora:
Requirements for listening to the Pandora
are as follows:
Requirements Aha™:
Requirements for listening to the Aha™ are
as follows:
iPhone or iPod touch
iPhone or iPod touch
• Use an Apple iPhone or iPod touch
running under iOS3 or later.
• Use an Apple iPhone or iPod touch
running iOS4 or later.
• Search for “Pandora”in the Apple iTunes
App Store to find and install the most
current version of the Pandora application
on your device.
• Search for “aha”in the Apple iTunes App
Store to find and install the most current
version of the Aha™ application on your
device.
• iPhone/ iPod touch connected to this unit • iPhone/ iPod touch connected to this unit
with a KCA-iP102.
with a KCA-iP102.
Android™ or BlackBerry®
Android™
• Download the Pandora application to
your smartphone from Pandora site using
it’s standard browser.
• Bluetooth must be built in and the
following profiles must be supported.
- SPP (Serial Port Profile)
- A2DP (Advanced Audio Distribution
Profile)
NOTE
• Use Android OS 2.2 or later.
• Download the Aha™ application to your
smartphone from the Google Play.
• Bluetooth must be built in and the
following profiles must be supported.
- SPP (Serial Port Profile)
- A2DP (Advanced Audio Distribution
Profile)
NOTE
• In the application on your device, log in
and create an account with Pandora.
(If you are not already a registered user,
an account can also be created at www.
pandora.com.)
• In the application on your device, log in
and create a free account with Aha.
• Internet connection by LTE, LTE, 3G, EDGE,
or WiFi.
• Because Aha™ is a third-party service,
the specifications are subject to change
without prior notice. Accordingly,
compatibility may be impaired or some
or all of the services may become
unavailable.
• Some Aha™ functionality cannot be
operated from this unit.
• aha, the Aha logo, and the Aha trade dress
are trademarks or registered trademarks
of HARMAN International Industries, used
with permission.
• Internet connection by LTE, LTE, 3G, EDGE,
or WiFi.
• Pandora is available only in the U.S,
Canada, Australia and New Zealand.
• Because Pandora is a third-party service,
the specifications are subject to change
without prior notice. Accordingly,
compatibility may be impaired or some
or all of the services may become
unavailable.
• Some functions of Pandora cannot be
operated from this unit.
• For issues using the application, please
contact Pandora at pandora-support@
pandora.com
• PANDORA, the PANDORA logo, and the
Pandora trade dress are trademarks or
registered trademarks of Pandora Media,
Inc., used with permission.
The marking of products using
lasers (Except for some areas)
CLASS 1
•
The Bluetooth word mark and logos are
owned by the Bluetooth SIG, Inc. and any use
of such marks by JVC KENWOOD Corporation
is under license. Other trademarks and trade
names are those of their respective owners.
The “AAC”logo is a trademark of Dolby
Laboratories.
“Made for iPod”and “Made for iPhone”
mean that an electronic accessory has been
designed to connect specifically to iPod or
iPhone, respectively, and has been certified
by the developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note
that the use of this accessory with iPod or
iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod
touch are trademarks of Apple Inc., registered
in the U.S. and other countries.
LASER PRODUCT
The label is attached to the chassis/case and
says that the component uses laser beams
that have been classified as Class 1. It means
that the unit is utilizing laser beams that
are of a weaker class. There is no danger of
hazardous radiation outside the unit.
•
•
TRA
REGISTERED No. : ER0106384/13
DEALER No. : 0016026/08
•
•
•
iTunes and Safari are trademark of Apple Inc.
IOS is a trademark or registered trademark of
Cisco in the U.S. and other countries and is
used under license.
•
Adobe, Acrobat and Reader are either
registered trademarks or trademarks of Adobe
Systems Incorporated in the United States
and/or other countries.
•
•
Android and Chrome are trademark of
Google Inc.
BlackBerry®, RIM®, Research In Motion® and
related trademarks, names and logos are the
property of Research In Motion Limited and
are registered and/or used in the U.S. and
countries around the world. Used under
license from Research In Motion Limited.
Internet Explorer and Windows Media are
registered trademark of Microsoft Corporation
in the United States and other countries.
Firefox is a registered trademark of Mozilla
Foundation in the United States and other
countries.
•
•
•
PANDORA, the PANDORA logo, and the
Pandora trade dress are trademarks or
registered trademarks of Pandora Media, Inc.,
used with permission.
•
aha, the Aha logo, and the Aha trade dress
are trademarks or registered trademarks of
HARMAN International Industries, used with
permission.
|